NETGEAR WN604 user manual Configure Basic QoS Settings

Page 21

Wireless N150 Access Point WN604

•Data rates for channel width = 2 0 MHz and guard interval=short (400 ms): Best, 7.2 Mbps, 14.4 Mbps, 21.7 Mbps, 28.9 Mbps, 43.3 Mbps, 57.8 Mbps, 65 Mbps, 72.2 Mbps.

•Data rates for channel width = 20 MHz and guard interval=long (800 ms): Best, 6.5 Mbps.

•Data rates for channel width = 40 MHz and guard interval=short: Best, 15 Mbps, 30 Mbps, 45 Mbps, 60 Mbps, 90 Mbps, 120 Mbps, 135 Mbps, 150 Mbps.

•Data rates for channel width = 40 MHz and guard interval=long: Best, 13.5 Mbps, 27 Mbps, 40.5 Mbps, 54 Mbps, 81 Mbps, 108Mbps, 121.5 Mbps, 135 Mbps.

Channel Width. From the drop-down list, select the desired channel width.

•20 MHz. This is the static, legacy mode. It gives the least throughput.

•40 MHz. This is the static, high-throughput mode. Legacy clients cannot connect in this mode.

•20/40 MHz. This is the dynamic, compatibility mode.

Guard Interval. From the drop-down list, select the desired guard interval. The guard interval protects from interference from other transmissions. The default is Auto.

Output Power. From the drop-down list, select the transmit power of the access point. The options are Full, Half, Quarter, Eighth, and Minimum. Decrease the transmit power if two or more APs are close together and use the same channel frequency. The default is Full. (The transmit power might vary depending on the local regulatory regulations.

Configure Basic QoS Settings

Wireless Multimedia (WMM) is a subset of the 802.11e standard. WMM allows wireless traffic to have a range of priorities, depending on the type of data.

Time-dependent information, such as video or audio, has a higher priority than normal traffic. For WMM to function correctly, wireless clients also have to support WMM.

Installation and Basic Configuration

21

Image 21

Contents Wireless N150 Access Point WN604 Technical Support Contents Appendix a Supplemental Information Getting Started Compatible Netgear Switches About the Access PointSystem Requirements What’s In the BoxHardware Description Front panel LEDs Front PanelWN604 rear panel Rear PanelProduct Label Side PanelInstallation and Basic Configuration  To log in to the access point Log In to the Access PointConfigure the System Settings for Your Location Install the Access Point To set up the access point for your location Set Basic IP Options Set the Time To configure the basic IP settings of your access point Deploy the Access Point Configure Wireless Access To configure your wireless settings for 11b/bg/ng  To deploy the access pointWireless Equipment Placement and Range Guidelines Verify Wireless ConnectivityWireless Settings Wireless Settings Screen Fields To configure the wireless settings Wireless N150 Access Point WN604 Configure Basic QoS Settings Set Up and Test Basic Wireless Connectivity  To set up and test wireless connectivitySelect Configuration Wireless Wireless N150 Access Point WN604 Configure Security  To configure a security profile Security ProfilesEdit Security Profile Screen Fields Authentication Settings Wireless Security Options Configure WPA2, or WPA2 + WPA, or WPA Manually Configure Security To configure WEP data encryption Configure WEP To configure WPS Wi-Fi Protected Setup WPSUse WPS to Add a Client to the Wireless Network  To add a client using the WPS button To add a client when logged in to the access point Restrict Wireless Access by MAC Address  To restrict access based on MAC addresses Management Upgrade the Wireless Access Point Firmware  To back up your current settings Configuration File Management To restore the factory settings  To change the administrator password Change the Administrator PasswordEnable the SysLog Server Activity Log System Screen Fields View Summary InformationNetwork Traffic Statistics  To access Statistics informationStatistic Screen Fields Available Wireless Station Statistics To view the available wireless stations Advanced Configuration Schedule the Wireless Radio Advanced Wireless Settings To schedule the wireless radio Advanced Wireless Settings Screen Fields  To configure advanced QoS settings Advanced QoS SettingsQoS queues and parameters Enable Wireless BridgingSelect the Enable Wireless Bridging check box  To configure bridging on your access pointWireless N150 Access Point WN604 Wireless point-to-point bridge setup Configure a Point-to-Point BridgeWireless point-to-multipoint bridge setup Configure a Point-to-Multi-Point Wireless BridgeWireless N150 Access Point WN604 Troubleshooting Troubleshooting with the LEDs WiFi LED Is OffAll LEDs Are Off Cannot Access the Internet or the LAN Wirelessly Cannot Connect to the Access Point to Configure ItLAN LED Is Off Time-Out Error Supplemental Information  To clear all data and restore the factory default values Factory Default SettingsAuto WN604 Technical Specifications Technical SpecificationsNotification of Compliance Netgear Wireless Routers, Gateways, APsNotification of Compliance FCC Requirements for Operation in the United States Industry Canada Interference Reduction Table Wireless N150 Access Point WN604 Notification of Compliance