NETGEAR WN604 user manual FCC Requirements for Operation in the United States

Page 65

Wireless N150 Access Point WN604

Svenska

Härmed intygar NETGEAR Inc. att denna Radiolan står I överensstämmelse med de

[Swedish]

väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv

 

1999/5/EG.

 

 

Íslenska

Hér með lýsir NETGEAR Inc. yfir því að Radiolan er í samræmi við grunnkröfur og aðrar

[Icelandic]

kröfur, sem gerðar eru í tilskipun 1999/5/EC.

 

 

Norsk

NETGEAR Inc. erklærer herved at utstyret Radiolan er i samsvar med de grunnleggende

[Norwegian]

krav og øvrige relevante krav i direktiv 1999/5/EF.

 

 

This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies.

In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services.

This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 - 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France.

FCC Requirements for Operation in the United States

FCC Information to User

This product does not contain any user serviceable components and is to be used with approved antennas only. Any product changes or modifications will invalidate all applicable regulatory certifications and approvals.

FCC Guidelines for Human Exposure

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC Declaration of Conformity

We, NETGEAR, Inc., 350 East Plumeria Drive, San Jose, CA 95134, declare under our sole responsibility that the Wireless N150 Access Point WN604 complies with Part 15 Subpart B of FCC CFR47 Rules. Operation is subject to the following two conditions:

•This device may not cause harmful interference, and

•This device must accept any interference received, including interference that may cause undesired operation.

FCC Radio Frequency Interference Warnings & Instructions

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following methods:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and the receiver.

•Connect the equipment into an electrical outlet on a circuit different from that which the radio receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Notification of Compliance

65

Page 64 Page 66
Image 65
Page 64 Page 66
Contents Wireless N150 Access Point WN604 Technical Support Contents Appendix a Supplemental Information Getting Started Compatible Netgear Switches About the Access PointHardware Description System RequirementsWhat’s In the Box Front panel LEDs Front PanelWN604 rear panel Rear PanelProduct Label Side PanelInstallation and Basic Configuration  To log in to the access point Log In to the Access PointConfigure the System Settings for Your Location Install the Access Point To set up the access point for your location Set Basic IP Options Set the Time To configure the basic IP settings of your access point Deploy the Access Point Configure Wireless Access To configure your wireless settings for 11b/bg/ng  To deploy the access pointWireless Equipment Placement and Range Guidelines Verify Wireless Connectivity To configure the wireless settings Wireless SettingsWireless Settings Screen Fields Wireless N150 Access Point WN604 Configure Basic QoS Settings Select Configuration Wireless Set Up and Test Basic Wireless Connectivity To set up and test wireless connectivity Wireless N150 Access Point WN604 Configure Security Edit Security Profile Screen Fields  To configure a security profileSecurity Profiles Authentication Settings Wireless Security Options Configure WPA2, or WPA2 + WPA, or WPA Manually Configure Security To configure WEP data encryption Configure WEP To configure WPS Wi-Fi Protected Setup WPS To add a client when logged in to the access point Use WPS to Add a Client to the Wireless Network To add a client using the WPS button Restrict Wireless Access by MAC Address  To restrict access based on MAC addresses Management Upgrade the Wireless Access Point Firmware  To back up your current settings Configuration File Management To restore the factory settings  To change the administrator password Change the Administrator PasswordEnable the SysLog Server Activity Log System Screen Fields View Summary InformationNetwork Traffic Statistics  To access Statistics informationStatistic Screen Fields Available Wireless Station Statistics To view the available wireless stations Advanced Configuration  To schedule the wireless radio Schedule the Wireless RadioAdvanced Wireless Settings Advanced Wireless Settings Screen Fields  To configure advanced QoS settings Advanced QoS SettingsQoS queues and parameters Enable Wireless BridgingSelect the Enable Wireless Bridging check box  To configure bridging on your access pointWireless N150 Access Point WN604 Wireless point-to-point bridge setup Configure a Point-to-Point BridgeWireless point-to-multipoint bridge setup Configure a Point-to-Multi-Point Wireless BridgeWireless N150 Access Point WN604 Troubleshooting All LEDs Are Off Troubleshooting with the LEDsWiFi LED Is Off LAN LED Is Off Cannot Access the Internet or the LAN WirelesslyCannot Connect to the Access Point to Configure It Time-Out Error Supplemental Information  To clear all data and restore the factory default values Factory Default SettingsAuto WN604 Technical Specifications Technical SpecificationsNotification of Compliance Netgear Wireless Routers, Gateways, APsNotification of Compliance FCC Requirements for Operation in the United States Industry Canada Interference Reduction Table Wireless N150 Access Point WN604 Notification of Compliance
Top Page Image Contents