Linksys BEFSR81 manual Pptp, Heart Beat Signal

Page 27

EtherFast Cable/DSL Router with 8-Port Switch

•Keep Alive Option and Redial Period. This option keeps your RAS-enabled Internet access connected indefinitely, even when it sits idle. To use this option, click the radio button next to Keep Alive. The default Redial Period is 30 seconds.

When you are finished, click the Save Settings button. Then click the Status tab, and click the Connect button to start the connection.

PPTP

Point to Point Tunneling Protocol (PPTP), shown in Figure 7-7, is a service that applies to connections in Europe and Israel only.

•IP Address. This is the IP address that the Router has, when seen from the Internet. Your ISP will provide you with the IP Address you need to specify here.

•Subnet Mask. This is the Router’s Subnet Mask, as seen by external users on the Internet (including your ISP). Your ISP will provide you with the Subnet Mask.

•Default Gateway. Your ISP will provide you with the Default Gateway Address.

•User Name and Password. Enter the User Name and Password provided by your ISP.

•Connect on Demand and Max Idle Time. You can configure the Router to cut your connection with your ISP after a specified period of time (Max Idle Time). If you have been disconnected due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio button. If you want your Internet connection to remain on at all times, enter 0 in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet access disconnects.

•Keep Alive Option and Redial Period. This option keeps your PPTP-enabled Internet access connected indefinitely, even when it sits idle. To use this option, click the radio button next to Keep Alive. The default Redial Period is 30 seconds.

When you are finished, click the Save Settings button. Then click the Status tab, and click the Connect button to start the connection.

Heart Beat Signal

Heart Beat Signal (shown in Figure 7-8) is a service used in Australia only. If you are using a Heart Beat Signal connection, check with your ISP for the necessary setup information.

Chapter 7: Using The Router’s Web-based Utility

Figure 7-7: PPTP

21

Basic Setup

Image 27

Contents Cable/DSL Router How to Use this Guide Copyright and TrademarksWord definition Table of Contents Ethernet Adapter Appendix a TroubleshootingCommon Problems and Solutions Frequently Asked Questions Appendix B Upgrading FirmwareBack Panel List of FiguresDdns Disabled Welcome IntroductionWhat’s in this Guide? EtherFast Cable/DSL Router with 8-Port Switch Networking Basics An Introduction to LANsUse of IP Addresses Networking Basics Use of IP Addresses Getting to Know the Router Reset Button Reset button can be used in one of two waysFront Panel Overview Connecting the RouterConnect a PC Connection InstructionsConfiguring Windows 98 and Millennium PCs Configuring the PCsConfiguring Windows XP PCs Configuring Windows 2000 PCsInternet Protocol TCP/IP for Windows XP Instructions Configuring the RouterStatic IP Obtain an IP Automatically or DhcpRAS PPPoEPptp Heart Beat SignalSecurity Using The Router’s Web-based UtilitySetup Navigating the Utility Status Quick and Easy Administration Administration Applications & GamingInternet Setup Basic SetupPPPoE RAS for SingTelPptp Heart Beat SignalNetwork Setup Optional SettingsRouter IP Ddns Network Address Server Settings DhcpMAC Address Clone DynDNS.orgTZO.com MAC Clone Advanced Routing14 Routing Table FilterBlock WAN Requests Filter IP Address RangeFilter Port Range Filter MAC AddressVPN Passthrough Port Range ForwardingPort Range Port Triggering Triggered RangeForwarded Range 20 UPnP Forwarding UPnP ForwardingDMZ QoS QoSApplication-based QoS Port-based QoS Router AccessLocal Router Access ManagementIdentification Remote Router AccessUPnP Log25 Incoming Log Table Factory DefaultsInformation Firmware UpgradeUpgrade Firmware Router31 Local Network Local NetworkFor Windows Appendix a TroubleshootingCommon Problems and Solutions For Windows 98 and MillenniumFor Windows XP For Windows 98 and Millennium EtherFast Cable/DSL Router with 8-Port Switch Need to set up a server behind my Router Am not able to access the Router’s Web-based Utility SetupTCP Application Start and End Protocol IP Address EnabledCan’t get the Internet game, server, or application to work For Netscape 4.7 or higher To start over, I need to set the Router to factory defaultNeed to upgrade the firmware For Microsoft Internet Explorer 5.0 or higherMy DSL service’s PPPoE is always disconnecting Firmware upgrade failedNeed to use port triggering Does the Router support IPX or AppleTalk? Frequently Asked QuestionsWhere is the Router installed on the network? Is IPSec Passthrough supported by the Router?How can I block corrupted FTP downloads? How many ports can be simultaneously forwarded? What is DMZ Hosting?Will the Router function in a Macintosh environment? Is the Router cross-platform compatible?How do I get mIRC to work with the Router? How can I check whether I have static or Dhcp IP addresses?Appendix B Upgrading Firmware Figure B-1 Upgrade FirmwareWindows 2000 or XP Instructions Windows 98 or Me InstructionsFigure C-3 MAC Address/Physical Address For the Router’s Web-based UtilityAppendix D Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Appendix E Glossary EtherFast Cable/DSL Router with 8-Port Switch EtherFast Cable/DSL Router with 8-Port Switch EtherFast Cable/DSL Router with 8-Port Switch EtherFast Cable/DSL Router with 8-Port Switch EtherFast Cable/DSL Router with 8-Port Switch Ports Appendix F SpecificationsEight 10/100 RJ-45 Switched Ports StandardsLimited Warranty Appendix G Warranty InformationFCC Statement Appendix H Regulatory InformationAppendix I Contact Information Need to contact Linksys?Information section in this Guide

Related manuals

Manual 26 pages 4.32 Kb