Linksys BEFSR81 manual Pptp, Heart Beat Signal

Page 22

EtherFast Cable/DSL Router with 8-Port Switch

PPTP

PPTP (shown in Figure 6-7) is a service used in Europe and Israel only. If you are using a PPTP connection, check with your ISP for the necessary setup information.

AWhen finished making your changes on this tab, click the Save Settings button to save this change, or click the Cancel Changes button to undo your change. For further help on this tab, click the Help button.

BClick the Status tab, and then click the Connect button. When you are finished, proceed to step 4.

Heart Beat Signal

Heart Beat Signal (shown in Figure 6-8) is a service used in Australia only. If you are using a Heart Beat Signal connection, check with your ISP for the necessary setup information.

AWhen finished making your changes on this tab, click the Save Settings button to save this change, or click the Cancel Changes button to undo your change. For further help on this tab, click the Help button.

BClick the Status tab, and then click the Connect button. When you are finished, proceed to step 4.

4.In the Optional Settings section, you may need to provide a Host Name and Domain Name for the Router. These fields are usually left blank. If requested by your ISP (usually cable ISPs), complete these two fields.

5.If you haven’t already done so, click the Save Settings button to save your settings. Close the web browser.

6.Reset the power on your cable or DSL modem.

7.Restart your computers so that they can obtain the Router’s new settings.

8.Congratulations! You’ve successfully configured the Router. Test the setup by opening your web browser from any computer and entering www.linksys.com/registration, as shown in Figure 6-9.

Figure 6-9: Router Registration for Basic Setup

If you are unable to reach our website, you may want to review what you did in this section or refer to “Appendix A: Troubleshooting.”

If you need advanced setting information, refer to “Chapter 7: Using the Router’s Web-based Utility” or

the Linksys support website at support.linksys.com.

Chapter 6: Configuring the Router

Figure 6-7: PPTP for Basic Setup

Figure 6-8: Heart Beat Signal for Basic Setup

16

Instructions

Image 22

Contents Cable/DSL Router Copyright and Trademarks How to Use this GuideWord definition Table of Contents Appendix B Upgrading Firmware Appendix a TroubleshootingCommon Problems and Solutions Frequently Asked Questions Ethernet AdapterList of Figures Back PanelDdns Disabled Introduction WelcomeWhat’s in this Guide? EtherFast Cable/DSL Router with 8-Port Switch An Introduction to LANs Networking BasicsUse of IP Addresses Networking Basics Use of IP Addresses Reset Button Reset button can be used in one of two ways Getting to Know the RouterFront Panel Connecting the Router OverviewConnection Instructions Connect a PCConfiguring the PCs Configuring Windows 98 and Millennium PCsConfiguring Windows 2000 PCs Configuring Windows XP PCsInternet Protocol TCP/IP for Windows XP Configuring the Router InstructionsObtain an IP Automatically or Dhcp Static IPPPPoE RASHeart Beat Signal PptpNavigating the Utility Using The Router’s Web-based UtilitySetup SecurityApplications & Gaming Quick and Easy AdministrationAdministration StatusBasic Setup Internet SetupRAS for SingTel PPPoEHeart Beat Signal PptpOptional Settings Network SetupRouter IP Network Address Server Settings Dhcp DdnsDynDNS.org MAC Address CloneTZO.com Advanced Routing MAC CloneFilter 14 Routing TableFilter MAC Address Filter IP Address RangeFilter Port Range Block WAN RequestsPort Range Forwarding VPN PassthroughPort Range Triggered Range Port TriggeringForwarded Range UPnP Forwarding 20 UPnP ForwardingDMZ QoS QoSApplication-based QoS Management Router AccessLocal Router Access Port-based QoSRemote Router Access IdentificationLog UPnPFactory Defaults 25 Incoming Log TableRouter Firmware UpgradeUpgrade Firmware InformationLocal Network 31 Local NetworkFor Windows 98 and Millennium Appendix a TroubleshootingCommon Problems and Solutions For WindowsFor Windows XP For Windows 98 and Millennium EtherFast Cable/DSL Router with 8-Port Switch Am not able to access the Router’s Web-based Utility Setup Need to set up a server behind my RouterApplication Start and End Protocol IP Address Enabled TCPCan’t get the Internet game, server, or application to work For Microsoft Internet Explorer 5.0 or higher To start over, I need to set the Router to factory defaultNeed to upgrade the firmware For Netscape 4.7 or higherFirmware upgrade failed My DSL service’s PPPoE is always disconnectingNeed to use port triggering Is IPSec Passthrough supported by the Router? Frequently Asked QuestionsWhere is the Router installed on the network? Does the Router support IPX or AppleTalk?How can I block corrupted FTP downloads? Is the Router cross-platform compatible? What is DMZ Hosting?Will the Router function in a Macintosh environment? How many ports can be simultaneously forwarded?How can I check whether I have static or Dhcp IP addresses? How do I get mIRC to work with the Router?Figure B-1 Upgrade Firmware Appendix B Upgrading FirmwareWindows 98 or Me Instructions Windows 2000 or XP InstructionsFor the Router’s Web-based Utility Figure C-3 MAC Address/Physical AddressShared Resources Appendix D Windows HelpNetwork Neighborhood/My Network Places Appendix E Glossary EtherFast Cable/DSL Router with 8-Port Switch EtherFast Cable/DSL Router with 8-Port Switch EtherFast Cable/DSL Router with 8-Port Switch EtherFast Cable/DSL Router with 8-Port Switch EtherFast Cable/DSL Router with 8-Port Switch Standards Appendix F SpecificationsEight 10/100 RJ-45 Switched Ports PortsAppendix G Warranty Information Limited WarrantyAppendix H Regulatory Information FCC StatementNeed to contact Linksys? Appendix I Contact InformationInformation section in this Guide

Related manuals

Manual 26 pages 4.32 Kb