Linksys RT31P2-NA manual Network Setup, Optional Settings, Router IP

Page 22

Broadband Router with 2 Phone Ports

Optional Settings

Some of these settings may be required by your ISP. Verify with your ISP before making any changes.

Host Name and Domain Name. These fields allow you to supply a host and domain name for the Router. Some ISPs require these names as identification. You may have to check with your ISP to see if your broadband Internet service has been configured with a host and domain name. In most cases, leaving these fields blank will work.

MTU. The MTU (Maximum Transmission Unit) setting specifies the largest packet size permitted for network transmission. Select Enable and enter the value desired. It is recommended that you leave this value in the 1200 to 1500 range. For most DSL users, it is recommended to use the value 1492. By default, MTU is set at 1500 when disabled.

Network Setup

The Network Setup section allows you to change the Router’s local network settings.

Router IP

The values for the Router’s Local IP Address and Subnet Mask are shown here. In most cases, keeping the default values will work.

Local IP Address. The default value is 192.168.15.1.

Subnet Mask. The default value is 255.255.255.0.

Network Address Server Settings (DHCP)

These settings allow you to configure the Router’s Dynamic Host Configuration Protocol (DHCP) server function. The Router can be used as a DHCP server for your network. A DHCP server automatically assigns an IP address to each computer on your network. Unless you already have one, it is highly recommended that you leave the Router enabled as a DHCP server.

Local DHCP Server. DHCP is enabled by factory default. If you already have a DHCP server on your network, set the Router’s DHCP option to Disable. If you disable DHCP, remember to assign a static IP address to the Router.

Start IP Address. Enter a value for the DHCP server to start with when issuing IP addresses. Because the default IP address for the Router is 192.168.15.1, the Start IP Address must be 192.168.15. 2 or greater, but smaller than 192.168.15.254. The default Start IP Address is 192.168.15.100.

Chapter 5: Configuring the Router

packet: a unit of data sent over a network

16

The Setup Tab - Basic Setup

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Broadband Router Copyright and Trademarks How to Use this GuideWord definition Table of Contents Appendix B Upgrading Firmware Appendix a TroubleshootingCommon Problems and Solutions Frequently Asked Questions Ethernet AdapterBack Panel Front Panel23 Applications & Gaming Tab DMZ Introduction WelcomeWhat’s in this Guide? Broadband Router with 2 Phone Ports An Introduction to Local Area Networks Networking BasicsUse of IP Addresses Networking Basics Use of IP Addresses Getting to Know the Router Phone2Front Panel Connecting the Router OverviewConnection Instructions Connect a PCSetup Configuring the RouterSecurity Applications & Gaming AdministrationVoice StatusInternet Setup How to Access the Web-based UtilitySetup Tab Basic Setup Internet Connection TypeStatic IP PPPoERAS for SingTel PptpHeart Beat Signal Heart Beat SignalNetwork Address Server Settings Dhcp Network SetupOptional Settings Router IPTime Setting DynDNS.org Setup Tab DdnsTZO.com Setup Tab MAC Address Clone MAC CloneSetup Tab Advanced Routing Advanced Routing13 Routing Table Entry List Filter Port Range Security Tab FilterFilter IP Address Range Filter MAC AddressConfiguring the Router Security Tab Filter Security Tab VPN Passthrough VPN PassthroughStun Settings Voice Tab SystemNAT Traversal Settings Voice Tab Line1 SettingsSubscriber Information Supplementary Service Settings Call Forward SettingsSpeed Dial Settings Distinctive Ring SettingsVoice Quality Settings Voice Tab Line2 Settings 19 Voice Tab Line2Configuring the Router Voice Tab Line2 Settings Voice Quality Settings Port Range Forwarding Applications & Gaming Tab Port Range ForwardingPort Range Triggered Range Applications & Gaming Tab Port TriggeringPort Triggering Forwarded RangeApplications & Gaming Tab UPnP Forwarding UPnP ForwardingBroadband Router with 2 Phone Ports Applications & Gaming Tab DMZ DMZApplication-based QoS Applications & Gaming Tab QoSPort-based QoS Voice QoS Local Router Access Administration Tab ManagementRouter Password Remote Router AccessBackup and Restore 26 Backup & Restore ConfigurationAdministration Tab Log LogAdministration Tab Factory Defaults Factory DefaultsAdministration Tab Firmware Upgrade Upgrade FirmwareLine1 Status Status Tab VoiceInformation Line2 StatusStatus Tab Router 33 Status Tab RouterStatus Tab Local Network Local NetworkAppendix a Troubleshooting Common Problems and SolutionsFor Windows For Windows 98 and MillenniumNeed to set a static IP address on a PC For Windows XP Want to test my Internet connectionFor Windows Am not able to access the Router’s Web-based Utility Setup Need to set up a server behind my Router Application Start and End Protocol IP Address Enabled TCPCan’t get the Internet game, server, or application to work For Microsoft Internet Explorer 5.0 or higher To start over, I need to set the Router to factory defaultNeed to upgrade the firmware For Netscape 4.7 or higherFirmware upgrade failed My DSL service’s PPPoE is always disconnectingNeed to use port triggering Frequently Asked Questions Does the Router support ICQ send file? If all else fails in the installation, what can I do?How can I block corrupted FTP downloads? Is the Router cross-platform compatible? What is DMZ Hosting?How many ports can be simultaneously forwarded? How can I check whether I have static or Dhcp IP addresses? Which modems are compatible with the Router?How do I get mIRC to work with the Router? Figure B-1 Upgrade Firmware Appendix B Upgrading FirmwareWindows 98 or Me Instructions Windows 2000 or XP InstructionsFor the Router’s Web-based Utility Figure C-3 MAC Address/Physical AddressShared Resources Appendix D Windows HelpNetwork Neighborhood/My Network Places Appendix E Glossary Broadband Router with 2 Phone Ports Broadband Router with 2 Phone Ports Broadband Router with 2 Phone Ports Broadband Router with 2 Phone Ports Appendix F Specifications Storage Humidity Storage TempOperating Humidity 0ºC to 40ºC 32ºF to 104ºFAppendix G Warranty Information Limited WarrantyAppendix H Regulatory Information FCC StatementNeed to contact Linksys? Appendix I Contact InformationInformation section in this Guide

RT31P2-NA specifications

The Linksys RT31P2-NA is a versatile voice-over-IP (VoIP) router designed to seamlessly combine internet connectivity with telephone services. Targeted at home users and small businesses, the device acts as a gateway through which users can connect multiple computers and internet-enabled devices while also facilitating digital phone services.

One of the standout features of the RT31P2-NA is its ability to support multiple voice lines, allowing users to make and receive calls while simultaneously using the internet. This dual functionality is made possible by its built-in VoIP capabilities, which leverage Session Initiation Protocol (SIP) technology, ensuring high-quality voice calls without interruptions from internet traffic.

In terms of connectivity, the router includes a standard Ethernet WAN port and four Ethernet LAN ports, providing ample options for wired connections to various devices. This setup is ideal for households or small offices that require stable, high-speed internet access across numerous devices. Additionally, the router features two telephone ports, allowing users to connect traditional analog phones directly for VoIP services.

Security is a key characteristic of the RT31P2-NA. It incorporates advanced security protocols such as WPA2 encryption and firewall capabilities to protect users' networks from unauthorized access and cyber threats. The router also supports Quality of Service (QoS) features, enabling users to prioritize bandwidth allocation for voice calls and other critical applications, ensuring minimal lag and superior call quality.

The design of the RT31P2-NA is user-friendly, with an intuitive interface that simplifies the setup process. The integrated configuration wizard helps users connect to their internet service and set up telephony services with ease. Furthermore, firmware updates can be easily managed, keeping the device secure and running optimally.

Moreover, Linksys is known for its reliable customer support and warranty services, which enhance the overall experience for users. The RT31P2-NA is a robust option for individuals and small businesses looking to streamline their communication needs while enjoying reliable internet connectivity. Whether for personal use or office applications, this router delivers a balanced mix of performance, functionality, and ease of use.
Top Page Image Contents