Linksys RT31P2 manual Routing Table Entry List

Page 33

Enter Route Name. Enter a name for the static route, using a maximum of 25 alphanumeric characters.

Destination LAN IP. The Destination LAN IP Address is the address of the remote network or host to which you want to assign a static route. Enter the IP address of the host for which you wish to create a static route.

Subnet Mask. The Subnet Mask determines which portion of a Destination IP address is the network portion, and which portion is the host portion.

Gateway. This is the IP address of the gateway device that allows for contact between the Router and the remote network or host.

Hop Count. This determines the maximum number of steps between network nodes that data packets will travel. A node is any device on the network, such as PCs, print servers, routers, etc.

Interface. Select Local or Internet, depending on the location of the static route’s final destination.

Delete Entry. If you need to delete a route, select its number from the drop-down menu, and click the Delete Entry button.

Show Routing Table. Click the Show Routing Table button to open a screen displaying how data is routed through your local network. For each route, the Destination LAN IP address, Subnet Mask, Default Gateway, Hop Count, and Interface are displayed. Click the Refresh button to update the information.

When you have finished making changes to this screen, click the Save Settings button to save the changes, or click the Cancel Changes button to undo your changes. Help information is shown on the right-hand side of a screen. For additional information, click More.

Chapter 5: Configuring the Router

Broadband Router with 2 Phone Ports

Figure 5-13: Routing Table Entry List

27

The Setup Tab - Advanced Routing

Image 33

Contents Broadband Router How to Use this Guide Copyright and TrademarksWord definition Table of Contents Common Problems and Solutions Frequently Asked Questions Appendix a TroubleshootingFront Panel Back Panel16 Security Tab VPN Passthrough Welcome IntroductionWhat’s in this Guide? Introduction What’s in this Guide? Broadband Router with 2 Phone Ports Networking Basics An Introduction to Local Area NetworksUse of IP Addresses Networking Basics Back Panel Getting to Know the RouterFront Panel Proceed to Connecting the Router Broadband Router with 2 Phone Ports Overview Connecting the RouterConnect a PC Connection InstructionsSetup Configuring the RouterSecurity VoiceApplications & Gaming How to Access the Web-based Utility AdministrationStatus Internet Setup Setup Tab Basic SetupInternet Connection Type Obtain an IP automaticallyPPPoE Static IPPPPoE RAS for SingTelPptp Heart Beat Signal Heart Beat SignalOptional Settings Network SetupRouter IP Packet a unit of data sent over a networkNetwork Address Server Settings Dhcp Time Setting Setup Tab DdnsTZO.com DynDNS.orgMAC Clone Setup Tab MAC Address CloneAdvanced Routing Setup Tab Advanced Routing13 Routing Table Entry List Filter IP Address Range Security Tab FilterFilter Port Range Filter MAC Address15 Filtered MAC Address Block WAN RequestsVPN Passthrough Security Tab VPN PassthroughApplications & Gaming Tab Port Range Forwarding Voice TabPort Range Forwarding Port RangeApplications & Gaming Tab Port Triggering Port TriggeringTriggered Range Applications & Gaming Tab UPnP Forwarding UPnP ForwardingForwarded Range Configuring the Router Broadband Router with 2 Phone Ports DMZ Applications & Gaming Tab DMZApplication-based QoS Applications & Gaming Tab QoSSpecific Port# fields Port-based QoSVoice QoS Router Password Administration Tab ManagementLocal Router Access Remote Router AccessUPnP Backup and RestoreLog Administration Tab LogAdministration Tab Factory Defaults Administration Tab Firmware UpgradeFirmware the programming code that runs a networking device Information Status Tab VoiceLine1 Status Line2 Status31 Status Tab Router Status Tab RouterLocal Network Status Tab Local NetworkCommon Problems and Solutions Appendix a TroubleshootingNeed to set a static IP address on a PC For Windows 98 and MillenniumFor Windows XP For WindowsWant to test my Internet connection For Windows XP Configuring the Router for details Am not able to access the Router’s Web-based Utility Setup Need to set up a server behind my Router TCP Application Start and End Protocol IP Address EnabledCan’t get the Internet game, server, or application to work Broadband Router with 2 Phone Ports My DSL service’s PPPoE is always disconnecting To start over, I need to set the Router to factory defaultFor Microsoft Internet Explorer 5.0 or higher For Netscape 4.7 or higherBroadband Router with 2 Phone Ports Need to use port triggering How do I make a phone call? Frequently Asked QuestionsCan I make calls if my Internet connection is down? Can I make calls while I’m browsing the Internet?Where is the Router installed on the network? Is IPSec Passthrough supported by the Router?Does the Router support IPX or AppleTalk? How can I block corrupted FTP downloads? Broadband Router with 2 Phone Ports If all else fails in the installation, what can I do? What is DMZ Hosting?Will the Router function in a Macintosh environment? How many ports can be simultaneously forwarded? Is the Router cross-platform compatible?Which modems are compatible with the Router? How can I check whether I have static or Dhcp IP addresses?Windows 98 or Me Instructions Figure B-1 IP Configuration ScreenFor the Router’s Web-based Utility Windows 2000 or XP InstructionsAppendix C Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Appendix C Windows Help Appendix D Glossary Appendix D Glossary Broadband Router with 2 Phone Ports Packet a unit of data sent over a network Broadband Router with 2 Phone Ports Broadband Router with 2 Phone Ports Two Standard Phone Ports, One Power Port Appendix E SpecificationsAppendix E Specifications Limited Warranty Appendix F Warranty InformationAppendix F Warranty Information FCC Statement Appendix G Regulatory InformationAppendix G Regulatory Information Appendix H Contact Information Appendix H Contact Information