Linksys RT31P2 manual Network Setup, Optional Settings, Router IP

Page 27

connection. If the connection is down, then the Router will automatically re-establish the connection. To use this option, click the radio button next to Keep Alive. The default Redial Period is 30 seconds.

When you are finished, click the Save Settings button. Then click the Status tab, and click the Connect button to start the connection.

Optional Settings

Some of these settings may be required by your ISP. Verify with your ISP before making any changes.

Host Name and Domain Name. These fields allow you to supply a host and domain name for the Router. Some ISPs require these names as identification. You may have to check with your ISP to see if your broadband Internet service has been configured with a host and domain name. In most cases, leaving these fields blank will work.

MTU. The MTU (Maximum Transmission Unit) setting specifies the largest packet size permitted for network transmission. Select Enable and enter the value desired. It is recommended that you leave this value in the 1200 to 1500 range. For most DSL users, it is recommended to use the value 1492. By default, MTU is set at 1500 when disabled.

Broadband Router with 2 Phone Ports

packet: a unit of data sent over a network

Network Setup

The Network Setup section allows you to change the Router’s local network settings.

Router IP

The values for the Router’s Local IP Address and Subnet Mask are shown here. In most cases, keeping the default values will work.

Chapter 5: Configuring the Router

21

The Setup Tab - Basic Setup

Image 27
Contents Broadband Router How to Use this Guide Copyright and TrademarksWord definition Table of Contents Common Problems and Solutions Frequently Asked Questions Appendix a TroubleshootingFront Panel Back Panel16 Security Tab VPN Passthrough Welcome IntroductionWhat’s in this Guide? Introduction What’s in this Guide? Broadband Router with 2 Phone Ports Networking Basics An Introduction to Local Area NetworksUse of IP Addresses Networking Basics Back Panel Getting to Know the RouterFront Panel Proceed to Connecting the Router Broadband Router with 2 Phone Ports Overview Connecting the RouterConnect a PC Connection InstructionsSetup Configuring the RouterSecurity VoiceApplications & Gaming How to Access the Web-based Utility AdministrationStatus Obtain an IP automatically Setup Tab Basic SetupInternet Setup Internet Connection TypePPPoE Static IPPPPoE RAS for SingTelPptp Heart Beat Signal Heart Beat SignalPacket a unit of data sent over a network Network SetupOptional Settings Router IPNetwork Address Server Settings Dhcp Time Setting Setup Tab DdnsTZO.com DynDNS.orgMAC Clone Setup Tab MAC Address CloneAdvanced Routing Setup Tab Advanced Routing13 Routing Table Entry List Filter MAC Address Security Tab FilterFilter IP Address Range Filter Port Range15 Filtered MAC Address Block WAN RequestsVPN Passthrough Security Tab VPN PassthroughPort Range Voice TabApplications & Gaming Tab Port Range Forwarding Port Range ForwardingApplications & Gaming Tab Port Triggering Port TriggeringTriggered Range Applications & Gaming Tab UPnP Forwarding UPnP ForwardingForwarded Range Configuring the Router Broadband Router with 2 Phone Ports DMZ Applications & Gaming Tab DMZApplication-based QoS Applications & Gaming Tab QoSSpecific Port# fields Port-based QoSVoice QoS Remote Router Access Administration Tab ManagementRouter Password Local Router AccessUPnP Backup and RestoreLog Administration Tab LogAdministration Tab Factory Defaults Administration Tab Firmware UpgradeFirmware the programming code that runs a networking device Line2 Status Status Tab VoiceInformation Line1 Status31 Status Tab Router Status Tab RouterLocal Network Status Tab Local NetworkCommon Problems and Solutions Appendix a TroubleshootingNeed to set a static IP address on a PC For Windows 98 and MillenniumFor Windows XP For WindowsWant to test my Internet connection For Windows XP Configuring the Router for details Am not able to access the Router’s Web-based Utility Setup Need to set up a server behind my Router TCP Application Start and End Protocol IP Address EnabledCan’t get the Internet game, server, or application to work Broadband Router with 2 Phone Ports For Netscape 4.7 or higher To start over, I need to set the Router to factory defaultMy DSL service’s PPPoE is always disconnecting For Microsoft Internet Explorer 5.0 or higherBroadband Router with 2 Phone Ports Need to use port triggering Can I make calls while I’m browsing the Internet? Frequently Asked QuestionsHow do I make a phone call? Can I make calls if my Internet connection is down?Where is the Router installed on the network? Is IPSec Passthrough supported by the Router?Does the Router support IPX or AppleTalk? How can I block corrupted FTP downloads? Broadband Router with 2 Phone Ports If all else fails in the installation, what can I do? What is DMZ Hosting?Will the Router function in a Macintosh environment? How can I check whether I have static or Dhcp IP addresses? Is the Router cross-platform compatible?How many ports can be simultaneously forwarded? Which modems are compatible with the Router?Windows 98 or Me Instructions Figure B-1 IP Configuration ScreenFor the Router’s Web-based Utility Windows 2000 or XP InstructionsAppendix C Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Appendix C Windows Help Appendix D Glossary Appendix D Glossary Broadband Router with 2 Phone Ports Packet a unit of data sent over a network Broadband Router with 2 Phone Ports Broadband Router with 2 Phone Ports Two Standard Phone Ports, One Power Port Appendix E SpecificationsAppendix E Specifications Limited Warranty Appendix F Warranty InformationAppendix F Warranty Information FCC Statement Appendix G Regulatory InformationAppendix G Regulatory Information Appendix H Contact Information Appendix H Contact Information