Linksys RT31P2 manual Windows 2000 or XP Instructions, For the Router’s Web-based Utility

Page 74

Broadband Router with 2 Phone Ports

Windows 2000 or XP Instructions

1.Click Start and Run. In the Open field, enter cmd. Press the Enter key or click the OK button.

2.At the command prompt, enter ipconfig /all. Then press the Enter key.

3.Write down the Physical Address as shown on your computer screen; it is the MAC address for your Ethernet adapter. This appears as a series of numbers and letters.

The MAC address/Physical Address is what you will use for MAC address cloning or MAC filtering.

The example shows the Ethernet adapter’s IP address as 192.168.1.100. Your computer may show something different.

For the Router’s Web-based Utility

For MAC address cloning, enter the 12-digit MAC address in the fields provided, two digits per field.

For MAC filtering, enter the 12-digit MAC address in this format, XXXXXXXXXXXX, WITHOUT the hyphens.

Figure B-3: MAC/Physical Address

Figure B-4: MAC Address Clone

	Figure B-5: MAC Address Filter
68	Appendix B: Finding the MAC Address and IP Address for Your Ethernet Adapter
	Windows 2000 or XP Instructions

Image 74

Contents Broadband Router Word definition How to Use this GuideCopyright and Trademarks Table of Contents Appendix a Troubleshooting Common Problems and Solutions Frequently Asked QuestionsBack Panel Front Panel16 Security Tab VPN Passthrough Introduction WelcomeWhat’s in this Guide? Introduction What’s in this Guide? Broadband Router with 2 Phone Ports Use of IP Addresses Networking BasicsAn Introduction to Local Area Networks Networking Basics Getting to Know the Router Back PanelFront Panel Proceed to Connecting the Router Broadband Router with 2 Phone Ports Connecting the Router OverviewConnection Instructions Connect a PCConfiguring the Router SetupApplications & Gaming SecurityVoice Status How to Access the Web-based UtilityAdministration Internet Connection Type Setup Tab Basic SetupInternet Setup Obtain an IP automaticallyStatic IP PPPoERAS for SingTel PPPoEPptp Heart Beat Signal Heart Beat SignalRouter IP Network SetupOptional Settings Packet a unit of data sent over a networkNetwork Address Server Settings Dhcp Setup Tab Ddns Time SettingDynDNS.org TZO.comSetup Tab MAC Address Clone MAC CloneSetup Tab Advanced Routing Advanced Routing13 Routing Table Entry List Filter Port Range Security Tab FilterFilter IP Address Range Filter MAC AddressBlock WAN Requests 15 Filtered MAC AddressSecurity Tab VPN Passthrough VPN PassthroughPort Range Forwarding Voice TabApplications & Gaming Tab Port Range Forwarding Port RangeTriggered Range Applications & Gaming Tab Port TriggeringPort Triggering Forwarded Range Applications & Gaming Tab UPnP ForwardingUPnP Forwarding Configuring the Router Broadband Router with 2 Phone Ports Applications & Gaming Tab DMZ DMZApplications & Gaming Tab QoS Application-based QoSPort-based QoS Specific Port# fieldsVoice QoS Local Router Access Administration Tab ManagementRouter Password Remote Router AccessBackup and Restore UPnPAdministration Tab Log LogFirmware the programming code that runs a networking device Administration Tab Factory DefaultsAdministration Tab Firmware Upgrade Line1 Status Status Tab VoiceInformation Line2 StatusStatus Tab Router 31 Status Tab RouterStatus Tab Local Network Local NetworkAppendix a Troubleshooting Common Problems and SolutionsFor Windows 98 and Millennium Need to set a static IP address on a PCFor Windows For Windows XPWant to test my Internet connection For Windows XP Configuring the Router for details Am not able to access the Router’s Web-based Utility Setup Need to set up a server behind my Router Application Start and End Protocol IP Address Enabled TCPCan’t get the Internet game, server, or application to work Broadband Router with 2 Phone Ports For Microsoft Internet Explorer 5.0 or higher To start over, I need to set the Router to factory defaultMy DSL service’s PPPoE is always disconnecting For Netscape 4.7 or higherBroadband Router with 2 Phone Ports Need to use port triggering Can I make calls if my Internet connection is down? Frequently Asked QuestionsHow do I make a phone call? Can I make calls while I’m browsing the Internet?Does the Router support IPX or AppleTalk? Where is the Router installed on the network?Is IPSec Passthrough supported by the Router? How can I block corrupted FTP downloads? Broadband Router with 2 Phone Ports Will the Router function in a Macintosh environment? If all else fails in the installation, what can I do?What is DMZ Hosting? Which modems are compatible with the Router? Is the Router cross-platform compatible?How many ports can be simultaneously forwarded? How can I check whether I have static or Dhcp IP addresses?Figure B-1 IP Configuration Screen Windows 98 or Me InstructionsWindows 2000 or XP Instructions For the Router’s Web-based UtilityNetwork Neighborhood/My Network Places Appendix C Windows HelpShared Resources Appendix C Windows Help Appendix D Glossary Appendix D Glossary Broadband Router with 2 Phone Ports Packet a unit of data sent over a network Broadband Router with 2 Phone Ports Broadband Router with 2 Phone Ports Appendix E Specifications Two Standard Phone Ports, One Power PortAppendix E Specifications Appendix F Warranty Information Limited WarrantyAppendix F Warranty Information Appendix G Regulatory Information FCC StatementAppendix G Regulatory Information Appendix H Contact Information Appendix H Contact Information