Linksys WRT54G3G-AT manual Wireless-G Router for Mobile Broadband

Page 61

Wireless-G Router for Mobile Broadband

4.I am not getting an IP address on the Internet with my Internet connection.

•Refer to “Problem #3, I want to test my Internet connection” to verify that you have connectivity.

•If you need to register the MAC address of your Ethernet adapter with your ISP, please see “Appendix E: Finding the MAC address and IP Address for Your Ethernet Adapter.” If you need to clone the MAC address of your Ethernet adapter onto the Router, see the System section of “Chapter 8: Configuring the Wireless-G Router for Mobile Broadband” for details.

•Make sure you are using the right Internet connection settings. Contact your ISP to see if your Internet connection type is DHCP, Static IP Address, or PPPoE (commonly used by DSL consumers). Please refer to the Setup section of “Chapter 8: Configuring the Wireless-G Router for Mobile Broadband” for details on Internet connection settings.

•Make sure you have the right cable. Check to see if the Internet column has a solidly lit Link/Act LED.

•Make sure the cable connecting from your cable or DSL modem is connected to the Router’s Internet port. Verify that the Status page of the Router’s web-based utility shows a valid IP address from your ISP.

•Turn off the computer, Router, and cable/DSL modem. Wait 30 seconds, and then turn on the Router, cable/DSL modem, and computer. Check the Status tab of the Router’s web-based utility to see if you get an IP address.

5.I am not able to access the Setup page of the Router’s web-based utility.

•Refer to “Problem #3, I want to test my Internet connection” to verify that your computer is properly connected to the Router.

•Refer to “Appendix E: Finding the MAC Address and IP address for Your Ethernet Adapter” to verify that your computer has an IP Address, Subnet Mask, Gateway, and DNS.

•Set a static IP address on your system; refer to “Problem #2: I need to set a static IP address.”

•Refer to “Problem #10: I am a PPPoE user, and I need to remove the proxy settings or the dial-up pop-up window.”

6.I need to set up a server behind my Router and make it available to the public.

To use a server like a web, ftp, or mail server, you need to know the respective port numbers they are using. For example, port 80 (HTTP) is used for web; port 21 (FTP) is used for FTP, and port 25 (SMTP outgoing) and port 110 (POP3 incoming) are used for the mail server. You can get more information by viewing the documentation provided with the server you installed.

Follow these steps to set up port forwarding through the Router’s web-based utility. We will be setting up web, ftp, and mail servers.

1.Access the Router’s web-based utility by going to http://192.168.1.1 or the IP address of the Router. Go to the Applications & Gaming => Port Range Forward tab.

2.Enter any name you want to use for the Application.

3.Enter the Start and End Port range of the service you are using. For example, if you have a web server, you would enter the range 80 to 80.

4.Select the protocol(s) you will be using, TCP and/or UDP.

Appendix A: Troubleshooting

52

Common Problems and Solutions

Page 60 Page 62
Image 61
Page 60 Page 62
Contents 802 GHz .11g Wireless- G Copyright and Trademarks How to Use This User GuideWord definition Table of Contents Appendix B Wireless Security Appendix a TroubleshootingCommon Problems and Solutions Frequently Asked Questions Appendix C Upgrading Firmware Appendix D Windows HelpRouter’s Ports List of Figures17 Setup Tab Advanced Routing Gateway 51 Status Tab Local Network Wireless-G Router for Mobile Broadband Wireless-G Router for Mobile Broadband Welcome IntroductionWhat’s in this User Guide? Wireless-G Router for Mobile Broadband Ad-Hoc versus Infrastructure Mode Planning Your Wireless NetworkSsid service set identifier your wireless network’s name Network TopologyPlanning Your Wireless Network Network Layout Router’s Ports Getting to Know the Wireless-G Router for Mobile BroadbandRouter’s LEDs are located on the Router’s other side panel Router’s LEDsRouter’s Data Card Slot Overview Connecting the Wireless-G Router for Mobile BroadbandConnect Your Computer Hardware Installation for Connection to Your Broadband Modem Connect the Power Diagram for Connection to Another Router Hardware Installation for Connection to Another RouterConnect Your Computer Stand Option Placement Options11 Measurement between Wall-Mount Slots Wall-Mount OptionPassword Screen Configuring the Wireless-G Router for Mobile BroadbandMobile Network Setup Setup Tab Basic SetupInternet Setup StatusStatic IP Connection Type L2TP Connection Type Optional SettingsDhcp Server Settings Network SetupNetwork Address Server Settings Dhcp Router IP12 Time Setting Time SettingMobile Network Connection Mode Setup Tab Mobile NetworkAPN Configuration Data Card Status Mobile Network StatusDynDNS.org Setup Tab DdnsTZO.com MAC Clone Setup Tab MAC Address CloneAdvanced Routing Setup Tab Advanced RoutingDynamic Routing Static RoutingWireless Network Wireless Tab Basic Wireless SettingsWireless Security Wireless Tab Wireless SecurityAES 26 Wireless Tab Wireless Security Radius Wireless MAC Filter Wireless Tab Wireless MAC FilterAdvanced Wireless Wireless Tab Advanced Wireless SettingsWireless-G Router for Mobile Broadband Firewall Security Tab FirewallBlock WAN Requests Internet Access Access Restrictions Tab Internet AccessTo create an Internet Access policy Security Tab VPN Passthrough34 Internet Policy Summary Port Range Forward Applications and Gaming Tab Port Range ForwardPort Triggering Applications & Gaming Tab Port TriggeringTriggered Range Forwarded RangeApplications and Gaming Tab DMZ Wired QoSApplications and Gaming Tab QoS Device PriorityEthernet Port Priority Wireless QoSApplication Priority Router Password Administration Tab ManagementUPnP Log Administration Tab LogPing Test Administration Tab DiagnosticsTraceroute Test Administration Tab Firmware Upgrade Administration Tab Factory DefaultsAdministration Tab Config Management 49 Status Tab Mobile Network Status Tab Mobile NetworkRouter Information Status Tab RouterInternet Local Network Status Tab Local NetworkWireless Status Tab WirelessCommon Problems and Solutions Appendix a TroubleshootingNeed to set a static IP address on a PC Wireless-G Router for Mobile Broadband Wireless-G Router for Mobile Broadband TCP Application Start and End Protocol IP Address EnabledCan’t get the Internet game, server, or application to work Need to upgrade the firmware To start over, I need to set the Router to factory defaultMy DSL service’s PPPoE is always disconnecting Power LED keeps flashing Where is the Router installed on the network? Frequently Asked QuestionsIs IPSec Pass-Through supported by the Router? Does the Router support IPX or AppleTalk?How will I be notified of new Router firmware upgrades? If all else fails in the installation, what can I do?How can I avoid corrupted FTP downloads? What are the advanced features of the Router? What is DMZ Hosting?Will the Router function in a Macintosh environment? Is the Router cross-platform compatible?What is the Ieee 802.11b standard? What is the Ieee 802.11g standard?What Ieee 802.11g features are supported? What Ieee 802.11b features are supported?What is roaming? What is infrastructure mode?What is ISM band? What is Spread Spectrum?What is WEP? What is DSSS? What is FHSS? And what are their differences?What is a MAC Address? How do I reset the Router?How do I connect to the mobile network? What do the indicator LEDs signify on the Router?Whom should I call if there is a question or problem? How do I know which mobile network I am using?Security Precautions Appendix B Wireless SecuritySecurity Threats Facing Wireless Networks Appendix B Wireless Security Wireless-G Router for Mobile Broadband Appendix C Upgrading Firmware Figure C-1 Upgrade FirmwareShared Resources Appendix D Windows HelpNetwork Neighborhood/My Network Places For the Router’s Web-based Utility Windows 2000 or XP InstructionsFigure E-4 MAC Address Filter List Appendix F Glossary Wireless-G Router for Mobile Broadband Wireless-G Router for Mobile Broadband Wireless-G Router for Mobile Broadband Wireless-G Router for Mobile Broadband Appendix G Specifications FCC, IC-03, CE, Wi-Fi 802.11b, 802.11g, WPA Appendix H Warranty Information Appendix I Regulatory Information Wireless-G Router for Mobile Broadband Wireless-G Router for Mobile Broadband Wireless-G Router for Mobile Broadband Wireless-G Router for Mobile Broadband Wireless-G Router for Mobile Broadband Wireless-G Router for Mobile Broadband

WRT54G3G-AT specifications

The Linksys WRT54G3G-AT is an advanced wireless router known for its versatility and robust performance in various networking environments. Designed particularly for users who require both wireless and mobile broadband connectivity, this device integrates several key features to cater to the needs of home users and small businesses alike.

One of the standout characteristics of the WRT54G3G-AT is its dual-connectivity option. It not only supports traditional broadband connections through DSL or cable but also offers 3G connectivity, making it ideal for users in areas where wired broadband options are limited or unreliable. With the ability to connect a compatible 3G USB modem, users can maintain internet access even during outages, ensuring continuous connectivity.

The WRT54G3G-AT utilizes the 802.11g wireless standard, providing speeds of up to 54 Mbps. This allows for efficient data transfer and seamless streaming, making it suitable for tasks such as online gaming and video conferencing. Its wireless range is optimized for both indoor and outdoor use, effectively covering medium-sized homes or office spaces without the need for additional access points.

Security is a crucial aspect of any networking device, and the WRT54G3G-AT incorporates advanced features to protect users' data. It supports security protocols such as WPA and WPA2, shielding against unauthorized access and ensuring that sensitive information remains secure. Additionally, the router offers a built-in firewall that adds another layer of protection against potential threats.

Another notable feature of the WRT54G3G-AT is its ease of installation and configuration. With a user-friendly web-based interface, even those with limited technical knowledge can set up the device without hassle. The installation process is streamlined, allowing users to quickly personalize their settings and connect their devices.

The router also includes a range of management tools, allowing users to monitor their network activity and optimize performance as needed. Quality of Service (QoS) settings enable users to prioritize bandwidth for specific applications, ensuring that critical tasks receive the necessary resources.

In summary, the Linksys WRT54G3G-AT is a powerful, flexible wireless router that combines traditional broadband functionality with mobile connectivity options. With robust performance features, security measures, and user-friendly management tools, it serves as an excellent choice for anyone seeking reliable internet access in a variety of environments.
Top Page Image Contents