Linksys WRT54G3G-AT manual Network Setup, Router IP, Dhcp Server Settings

Page 30

Wireless-G Router for Mobile Broadband

MTU. MTU is the Maximum Transmission Unit. It specifies the largest packet size permitted for Internet transmission. The default setting, Manual, allows you to enter the largest packet size that will be transmitted. The recommended size, entered in the Size field, is 1492. You should leave this value in the 1200 to 1500 range. To have the Router select the best MTU for your Internet connection, select Auto.

Network Setup

The Network Setup section changes the settings on the network connected to the Router’s Ethernet ports. Wireless setup is performed through the Wireless tab.

Router IP

This presents both the Router’s IP Address and Subnet Mask as seen by your network.

DHCP Server Settings

The Router can be used as a Dynamic Host Configuration Protocol (DHCP) server for your network. A DHCP server automatically assigns an IP address to each computer on your network. Select the mode you want the Router to use for its DHCP server function. If you are not sure which mode to select, keep the default, Mode 1 - Fixed configuration (Default).

Mode 1 - Fixed configuration (Default). In this mode, the Router will advertise itself as the DNS server for the clients (computers) to use. The clients will contact the Router for DNS, and its DNS caching server will resolve the addresses for them. This mode is recommended for networks whose UMTS upstream DNS servers change on a connection-by-connection basis, such as networks in the UK.

Mode 2- Network Supplied. Via DHCP, the Router will advertise the DNS and WINS servers it is using. This mode may be suitable for networks whose DNS servers have static addresses.

Mode 3- Manual configuration. You can designate the settings advertised to the clients via DHCP. Complete the Static DNS and WINS fields that will appear. You can specify up to three DNS servers and up to two WINS servers. Make sure these values do not depend on the Router’s static settings.

Network Address Server Settings (DHCP)

The settings allow you to configure the Router’s Dynamic Host Configuration Protocol (DHCP) server function. The Router can be used as a DHCP server for your network. A DHCP server automatically assigns an IP address to each computer on your network. If you choose to enable the Router’s DHCP server option, you must configure all of your network PCs to connect to a DHCP server (the Router), and make sure there is no other DHCP server on your network.

Chapter 5: Configuring the Wireless-G Router for Mobile Broadband

Figure 5-9: Router IP

Figure 5-10: DHCP Server Setttings

Figure 5-11: Network Address Server Settings

21

The Setup Tab - Basic Setup

Page 29 Page 31
Image 30
Page 29 Page 31
Contents 802 GHz .11g Wireless- G How to Use This User Guide Copyright and TrademarksWord definition Table of Contents Common Problems and Solutions Frequently Asked Questions Appendix a TroubleshootingAppendix B Wireless Security Appendix C Upgrading Firmware Appendix D Windows HelpList of Figures Router’s Ports17 Setup Tab Advanced Routing Gateway 51 Status Tab Local Network Wireless-G Router for Mobile Broadband Wireless-G Router for Mobile Broadband Introduction WelcomeWhat’s in this User Guide? Wireless-G Router for Mobile Broadband Ssid service set identifier your wireless network’s name Planning Your Wireless NetworkAd-Hoc versus Infrastructure Mode Network TopologyPlanning Your Wireless Network Network Layout Getting to Know the Wireless-G Router for Mobile Broadband Router’s PortsRouter’s LEDs Router’s LEDs are located on the Router’s other side panelRouter’s Data Card Slot Connecting the Wireless-G Router for Mobile Broadband OverviewConnect Your Computer Hardware Installation for Connection to Your Broadband Modem Connect the Power Hardware Installation for Connection to Another Router Diagram for Connection to Another RouterConnect Your Computer Placement Options Stand OptionWall-Mount Option 11 Measurement between Wall-Mount SlotsConfiguring the Wireless-G Router for Mobile Broadband Password ScreenInternet Setup Setup Tab Basic SetupMobile Network Setup StatusStatic IP Connection Type Optional Settings L2TP Connection TypeNetwork Address Server Settings Dhcp Network SetupDhcp Server Settings Router IPTime Setting 12 Time SettingSetup Tab Mobile Network Mobile Network Connection ModeAPN Configuration Mobile Network Status Data Card StatusSetup Tab Ddns DynDNS.orgTZO.com Setup Tab MAC Address Clone MAC CloneDynamic Routing Setup Tab Advanced RoutingAdvanced Routing Static RoutingWireless Tab Basic Wireless Settings Wireless NetworkWireless Tab Wireless Security Wireless SecurityAES 26 Wireless Tab Wireless Security Radius Wireless Tab Wireless MAC Filter Wireless MAC FilterWireless Tab Advanced Wireless Settings Advanced WirelessWireless-G Router for Mobile Broadband Security Tab Firewall FirewallBlock WAN Requests To create an Internet Access policy Access Restrictions Tab Internet AccessInternet Access Security Tab VPN Passthrough34 Internet Policy Summary Applications and Gaming Tab Port Range Forward Port Range ForwardTriggered Range Applications & Gaming Tab Port TriggeringPort Triggering Forwarded RangeApplications and Gaming Tab QoS Wired QoSApplications and Gaming Tab DMZ Device PriorityWireless QoS Ethernet Port PriorityApplication Priority Administration Tab Management Router PasswordUPnP Administration Tab Log LogAdministration Tab Diagnostics Ping TestTraceroute Test Administration Tab Factory Defaults Administration Tab Firmware UpgradeAdministration Tab Config Management Status Tab Mobile Network 49 Status Tab Mobile NetworkStatus Tab Router Router InformationInternet Status Tab Local Network Local NetworkStatus Tab Wireless WirelessAppendix a Troubleshooting Common Problems and SolutionsNeed to set a static IP address on a PC Wireless-G Router for Mobile Broadband Wireless-G Router for Mobile Broadband Application Start and End Protocol IP Address Enabled TCPCan’t get the Internet game, server, or application to work To start over, I need to set the Router to factory default Need to upgrade the firmwareMy DSL service’s PPPoE is always disconnecting Power LED keeps flashing Is IPSec Pass-Through supported by the Router? Frequently Asked QuestionsWhere is the Router installed on the network? Does the Router support IPX or AppleTalk?If all else fails in the installation, what can I do? How will I be notified of new Router firmware upgrades?How can I avoid corrupted FTP downloads? Will the Router function in a Macintosh environment? What is DMZ Hosting?What are the advanced features of the Router? Is the Router cross-platform compatible?What Ieee 802.11g features are supported? What is the Ieee 802.11g standard?What is the Ieee 802.11b standard? What Ieee 802.11b features are supported?What is ISM band? What is infrastructure mode?What is roaming? What is Spread Spectrum?What is a MAC Address? What is DSSS? What is FHSS? And what are their differences?What is WEP? How do I reset the Router?What do the indicator LEDs signify on the Router? How do I connect to the mobile network?How do I know which mobile network I am using? Whom should I call if there is a question or problem?Appendix B Wireless Security Security PrecautionsSecurity Threats Facing Wireless Networks Appendix B Wireless Security Wireless-G Router for Mobile Broadband Figure C-1 Upgrade Firmware Appendix C Upgrading FirmwareAppendix D Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Windows 2000 or XP Instructions For the Router’s Web-based UtilityFigure E-4 MAC Address Filter List Appendix F Glossary Wireless-G Router for Mobile Broadband Wireless-G Router for Mobile Broadband Wireless-G Router for Mobile Broadband Wireless-G Router for Mobile Broadband Appendix G Specifications FCC, IC-03, CE, Wi-Fi 802.11b, 802.11g, WPA Appendix H Warranty Information Appendix I Regulatory Information Wireless-G Router for Mobile Broadband Wireless-G Router for Mobile Broadband Wireless-G Router for Mobile Broadband Wireless-G Router for Mobile Broadband Wireless-G Router for Mobile Broadband Wireless-G Router for Mobile Broadband

WRT54G3G-AT specifications

The Linksys WRT54G3G-AT is an advanced wireless router known for its versatility and robust performance in various networking environments. Designed particularly for users who require both wireless and mobile broadband connectivity, this device integrates several key features to cater to the needs of home users and small businesses alike.

One of the standout characteristics of the WRT54G3G-AT is its dual-connectivity option. It not only supports traditional broadband connections through DSL or cable but also offers 3G connectivity, making it ideal for users in areas where wired broadband options are limited or unreliable. With the ability to connect a compatible 3G USB modem, users can maintain internet access even during outages, ensuring continuous connectivity.

The WRT54G3G-AT utilizes the 802.11g wireless standard, providing speeds of up to 54 Mbps. This allows for efficient data transfer and seamless streaming, making it suitable for tasks such as online gaming and video conferencing. Its wireless range is optimized for both indoor and outdoor use, effectively covering medium-sized homes or office spaces without the need for additional access points.

Security is a crucial aspect of any networking device, and the WRT54G3G-AT incorporates advanced features to protect users' data. It supports security protocols such as WPA and WPA2, shielding against unauthorized access and ensuring that sensitive information remains secure. Additionally, the router offers a built-in firewall that adds another layer of protection against potential threats.

Another notable feature of the WRT54G3G-AT is its ease of installation and configuration. With a user-friendly web-based interface, even those with limited technical knowledge can set up the device without hassle. The installation process is streamlined, allowing users to quickly personalize their settings and connect their devices.

The router also includes a range of management tools, allowing users to monitor their network activity and optimize performance as needed. Quality of Service (QoS) settings enable users to prioritize bandwidth for specific applications, ensuring that critical tasks receive the necessary resources.

In summary, the Linksys WRT54G3G-AT is a powerful, flexible wireless router that combines traditional broadband functionality with mobile connectivity options. With robust performance features, security measures, and user-friendly management tools, it serves as an excellent choice for anyone seeking reliable internet access in a variety of environments.
Top Page Image Contents