Linksys WRT150N manual Status Tab Wireless

Page 54

Wireless-N Home Router

The Status Tab - Wireless

The Wireless screen displays the status information of your wireless network.

Wireless

MAC Address. The MAC Address of the Router’s wireless interface is displayed here.

Mode. Displayed here is the wireless mode (Mixed, Wireless-N Only, Wireless-G Only, Wireless-B Only, or Disabled) used by the network.

Network Name (SSID). Displayed here is the name of the wireless network or SSID.

Radio Band. Displayed here is the Radio Band setting selected on the Basic Wireless Settings screen. Wide Channel. Displayed here is the Wide Channel setting selected on the Basic Wireless Settings screen. Standard Channel. Shown here is the Standard Channel setting selected on the Basic Wireless Settings screen. Security. Displayed here is the wireless security method used by the Router.

SSID Broadcast. Displayed here is the status of the SSID Broadcast feature.

For more information, click Help.

Chapter 5: Configuring the Wireless-N Home Router

Figure 5-51: Status Tab - Wireless

48

The Status Tab - Wireless

Image 54

Contents GHz Wireless- N How to Use This User Guide Copyright and TrademarksWord definition Table of Contents Common Problems and Solutions Frequently Asked Questions Appendix a TroubleshootingAppendix B Wireless Security Appendix C Upgrading Firmware Appendix D Windows HelpRouter’s Back Panel Router’s Front Panel26 Access Restrictions Tab Internet Access Policy Introduction WelcomeWhat’s in this User Guide? Wireless-N Home Router Ssid service set identifier your wireless network’s name Planning Your Wireless NetworkAd-Hoc versus Infrastructure Mode Network TopologyPlanning Your Wireless Network Network Layout Getting to Know the Wireless-N Home Router Back PanelFront Panel Top PanelConnecting the Wireless-N Home Router Hardware InstallationWireless Configuring the Wireless-N Home RouterSetup OverviewSecurity Access RestrictionsAdministration Applications & GamingInternet Setup How to Access the Web-based UtilitySetup Tab Basic Setup StatusStatic IP PPPoEPptp Telstra CableOptional Settings Packet a unit of data sent over a networkNetwork Setup Dhcp Server SettingRouter IP Time Setting Dhcp ReservationSetup Tab Ddns Ddns ServiceDynDNS.org 10 Setup Tab Ddns TZO.com TZO.comSetup Tab MAC Address Clone MAC Address CloneDynamic Routing Setup Tab Advanced RoutingAdvanced Routing Static Routing13 Routing Table Wireless Tab Basic Wireless Settings Basic Wireless SettingsPSK-Personal Wireless Tab Wireless SecurityWireless Security PSK2-PersonalPSK-Enterprise PSK2-EnterpriseRadius Access Restrictions Wireless Tab Wireless MAC FilterWireless MAC Filter MAC Address Filter ListWireless Tab Advanced Wireless Settings Advanced WirelessWireless-N Home Router Web Filter Security Tab FirewallInternet Filter FirewallSecurity Tab VPN Passthrough VPN PassthroughAccess Restrictions Tab Internet Access Policy Internet Access PolicyTo create a policy 28 List of PCs Applications & Gaming Tab Single Port Forwarding Single Port ForwardingApplications & Gaming Tab Port Range Forwarding Port Range ForwardingApplications & Gaming Tab Port Range Triggering Port Range TriggeringApplications & Gaming Tab DMZ DMZInternet Access Priority QoS Quality of ServiceWireless Applications and Gaming Tab QoS35 QoS Applications Add a New Application Summary 39 QoS Voice DeviceWeb Access Administration Tab ManagementRouter Access Remote AccessBackup and Restore UPnPAdministration Tab Log LogAdministration Tab Diagnostics 43 Administration Tab DiagnosticsAdministration Tab Factory Defaults Factory DefaultsAdministration Tab Firmware Upgrade Upgrade FirmwareStatus Tab Router Router InformationInternet Connection Status Tab Local Network Local NetworkStatus Tab Wireless 51 Status Tab WirelessAppendix a Troubleshooting Common Problems and SolutionsNeed to set a static IP address on a PC Wireless-N Home Router Open a command prompt. For Windows 98SE and Me Protocol To IP Address Enabled Application NameApplication Name Start and End Port Can’t get the Internet game, server, or application to workWireless-N Home Router Firmware upgrade failed, and/or the Power LED is flashing To start over, I need to set the Router to factory defaultsNeed to upgrade the firmware My DSL service’s PPPoE is always disconnectingPower LED keeps flashing Is IPSec Pass-Through supported by the Router? Frequently Asked QuestionsWhere is the Router installed on the network? Does the Router support IPX or AppleTalk?How can I block corrupted FTP downloads? Will the Router function in a Macintosh environment? What is DMZ Hosting?What are the advanced features of the Router? Is the Router cross-platform compatible?What Ieee 802.11g features are supported? What is the Ieee 802.11g standard?What is the Ieee 802.11b standard? What Ieee 802.11b features are supported?What is ISM band? What is infrastructure mode?What is roaming? What is Spread Spectrum?How do I reset the Router? What is DSSS? What is FHSS? And what are their differences?What is a MAC Address? How do I resolve issues with signal loss?Appendix B Wireless Security Security PrecautionsSecurity Threats Facing Wireless Networks Appendix B Wireless Security Wireless-N Home Router Figure C-1 Firmware Upgrade Appendix C Upgrading FirmwareAppendix D Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Figure E-1 IP Configuration Screen Windows 98SE or Me InstructionsWindows 2000 or XP Instructions For the Router’s Web-based UtilityAppendix F Glossary Wireless-N Home Router Wireless-N Home Router Wireless-N Home Router Wireless-N Home Router Appendix G Specifications ModelLEDs Operating Humidity Operating TempStorage Temp Storage HumidityAppendix H Warranty Information Limited WarrantyAppendix I Regulatory Information FCC StatementWireless-N Home Router Wireless-N Home Router Wireless-N Home Router Wireless-N Home Router Wireless-G Home Router Appendix J Contact Information Need to contact Linksys?Information section in this Guide