Linksys WRT150N manual Optional Settings, Packet a unit of data sent over a network

Page 20

Wireless-N Home Router

L2TP

Layer 2 Tunneling Protocol (L2TP) is a service that tunnels Point-to-Point Protocol (PPP) across the Internet. It is used mostly in European countries. Check with your ISP for the necessary setup information.

Server IP Address. This is the IP address that the Router has, when seen from the Internet. Your ISP will provide you with the IP address you need to specify here.

User Name and Password. Enter the User Name and Password provided by your ISP.

Connect on Demand and Max Idle Time. You can configure the Router to cut the Internet connection after it has been inactive for a specific period of time (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. To use Connect on Demand, click the radio button. If you want your Internet connection to remain on at all times, enter 0 in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet access disconnects.

Keep Alive and Redial Period. This option keeps your Internet access connected indefinitely, even when it sits idle. If you select this option, the Router will periodically check your Internet connection. If the connection is down, then the Router will automatically re-establish the connection. To use this option, click the radio button next to Keep Alive. The default Redial Period is 30 seconds.

Click the Save Settings button. Then click the Status tab, and click the Connect button.

Optional Settings

Some of these settings may be required by your ISP. Verify with your ISP before making any changes.

Host Name and Domain Name. Some ISPs require these names as identification. You may have to check with your ISP to see if your broadband Internet service has been configured with a host and domain name. In most cases, leaving these fields blank will work.

MTU. The MTU (Maximum Transmission Unit) setting specifies the largest packet size permitted for network transmission. To manually set a value, select Manual and enter the value desired in the Size field. You should leave this value in the 1200 to 1500 range. Most DSL users should use the value 1492. The default is Auto, which allows the Router to select the best MTU for your Internet connection.

Chapter 5: Configuring the Wireless-N Home Router

Figure 5-7: L2TP

packet: a unit of data sent over a network.

14

The Setup Tab - Basic Setup

Image 20
Contents GHz Wireless- N Word definition How to Use This User GuideCopyright and Trademarks Table of Contents Appendix a Troubleshooting Appendix B Wireless SecurityCommon Problems and Solutions Frequently Asked Questions Appendix C Upgrading Firmware Appendix D Windows HelpRouter’s Back Panel Router’s Front Panel26 Access Restrictions Tab Internet Access Policy Introduction WelcomeWhat’s in this User Guide? Wireless-N Home Router Planning Your Wireless Network Ad-Hoc versus Infrastructure ModeSsid service set identifier your wireless network’s name Network TopologyPlanning Your Wireless Network Network Layout Getting to Know the Wireless-N Home Router Back PanelFront Panel Top PanelConnecting the Wireless-N Home Router Hardware InstallationConfiguring the Wireless-N Home Router SetupWireless OverviewAccess Restrictions AdministrationSecurity Applications & GamingHow to Access the Web-based Utility Setup Tab Basic SetupInternet Setup StatusStatic IP PPPoEPptp Telstra CableOptional Settings Packet a unit of data sent over a networkRouter IP Network SetupDhcp Server Setting Time Setting Dhcp ReservationDynDNS.org Setup Tab DdnsDdns Service 10 Setup Tab Ddns TZO.com TZO.comSetup Tab MAC Address Clone MAC Address CloneSetup Tab Advanced Routing Advanced RoutingDynamic Routing Static Routing13 Routing Table Wireless Tab Basic Wireless Settings Basic Wireless SettingsWireless Tab Wireless Security Wireless SecurityPSK-Personal PSK2-PersonalPSK-Enterprise PSK2-EnterpriseRadius Wireless Tab Wireless MAC Filter Wireless MAC FilterAccess Restrictions MAC Address Filter ListWireless Tab Advanced Wireless Settings Advanced WirelessWireless-N Home Router Security Tab Firewall Internet FilterWeb Filter FirewallSecurity Tab VPN Passthrough VPN PassthroughTo create a policy Access Restrictions Tab Internet Access PolicyInternet Access Policy 28 List of PCs Applications & Gaming Tab Single Port Forwarding Single Port ForwardingApplications & Gaming Tab Port Range Forwarding Port Range ForwardingApplications & Gaming Tab Port Range Triggering Port Range TriggeringApplications & Gaming Tab DMZ DMZQoS Quality of Service WirelessInternet Access Priority Applications and Gaming Tab QoS35 QoS Applications Add a New Application Summary 39 QoS Voice DeviceAdministration Tab Management Router AccessWeb Access Remote AccessBackup and Restore UPnPAdministration Tab Log LogAdministration Tab Diagnostics 43 Administration Tab DiagnosticsAdministration Tab Factory Defaults Factory DefaultsAdministration Tab Firmware Upgrade Upgrade FirmwareInternet Connection Status Tab RouterRouter Information Status Tab Local Network Local NetworkStatus Tab Wireless 51 Status Tab WirelessNeed to set a static IP address on a PC Appendix a TroubleshootingCommon Problems and Solutions Wireless-N Home Router Open a command prompt. For Windows 98SE and Me Protocol To IP Address Enabled Application NameApplication Name Start and End Port Can’t get the Internet game, server, or application to workWireless-N Home Router To start over, I need to set the Router to factory defaults Need to upgrade the firmwareFirmware upgrade failed, and/or the Power LED is flashing My DSL service’s PPPoE is always disconnectingPower LED keeps flashing Frequently Asked Questions Where is the Router installed on the network?Is IPSec Pass-Through supported by the Router? Does the Router support IPX or AppleTalk?How can I block corrupted FTP downloads? What is DMZ Hosting? What are the advanced features of the Router?Will the Router function in a Macintosh environment? Is the Router cross-platform compatible?What is the Ieee 802.11g standard? What is the Ieee 802.11b standard?What Ieee 802.11g features are supported? What Ieee 802.11b features are supported?What is infrastructure mode? What is roaming?What is ISM band? What is Spread Spectrum?What is DSSS? What is FHSS? And what are their differences? What is a MAC Address?How do I reset the Router? How do I resolve issues with signal loss?Security Threats Facing Wireless Networks Appendix B Wireless SecuritySecurity Precautions Appendix B Wireless Security Wireless-N Home Router Figure C-1 Firmware Upgrade Appendix C Upgrading FirmwareNetwork Neighborhood/My Network Places Appendix D Windows HelpShared Resources Figure E-1 IP Configuration Screen Windows 98SE or Me InstructionsWindows 2000 or XP Instructions For the Router’s Web-based UtilityAppendix F Glossary Wireless-N Home Router Wireless-N Home Router Wireless-N Home Router Wireless-N Home Router LEDs Appendix G SpecificationsModel Operating Temp Storage TempOperating Humidity Storage HumidityAppendix H Warranty Information Limited WarrantyAppendix I Regulatory Information FCC StatementWireless-N Home Router Wireless-N Home Router Wireless-N Home Router Wireless-N Home Router Wireless-G Home Router Information section in this Guide Appendix J Contact InformationNeed to contact Linksys?