CONNECTING THE REMOTE CONTROL JACKS
|
|
|
| INPUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1 |
|
|
|
|
| INPUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| 3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| COMPONENT |
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| VIDEO |
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| MONITOR |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| OUT |
|
|
| 2 |
|
|
|
|
|
| INPUT |
|
|
|
|
|
|
|
| INPUT 1 |
|
| |
DVD | VCR IN | VCR OUT | DSS | MONITOR OUT 2 | Y CB/PB | CR/PR | Y | CB/PB | CR/PR |
|
|
|
| |||
IN |
|
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| 3 | 4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| RC OUT |
|
| IN | OUT |
| IN | OUT | IN | OUT | 1 | 2 | OPT | OUT | FLASHER |
|
| OPTION | |
|
|
|
|
|
| |||||||||||
DVD | VCR | DSS | AUDIO | TAPE | CD/CDR | DIGITAL IN | DIGITAL OUT REMOTE CONT. |
| IN |
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
| AC IN |
|
|
|
|
| R | L | R | L | R | L |
|
|
| AC OUTLETS |
|
|
|
| |
|
|
|
|
| 120V 60Hz |
|
|
|
| |||||||
|
| FRONT | SURROUND BACK | SURROUND | CENTER |
| SWITCHED |
| 1 |
|
| |||||
|
|
|
| S. SPEAKER B |
|
|
|
|
| 1.25A 150W |
|
|
| |||
|
|
|
| SPEAKER SYSTEMS : |
|
|
|
|
| MODEL N |
|
| ||||
REMOTE |
|
| CD recorder |
|
| REMOTE |
|
| DVD player | REMOTE | CD player | |||||
CONTROL |
|
|
|
|
|
|
|
| CONTROL |
|
|
|
| CONTROL |
| |
IN |
|
|
|
|
|
|
|
|
| IN |
|
|
|
| IN |
|
OUT |
|
|
|
|
|
|
|
| OUT |
|
|
|
| OUT |
| |
|
|
|
| EXTERNAL INTERNAL |
|
|
|
|
| EXTERNAL INTERNAL |
| EXTERNAL INTERNAL |
q
You can control other Marantz products through this unit with the remote controller by connecting the REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote controller is received by the remote sensor on this unit. Then the signal is sent to the connected device through this terminal. Therefore you need to aim the remote signal only to the unit. Also, if a Marantz power amplifier (some models excluded) is connected to one of these terminals, the power amplifier’s, power switch is synchronized with this unit’s power switch.
Set the REMOTE CONTROL SWITCH on the back of other units (not the SR4003) to “EXT”.(EXTERNAL) to use this feature.
| ENGLISH |
|
| |
w |
| ANDNAMES | FUNCTIONS | |
Whenever external infrared sensors or similar | ||||
|
| |||
devices are connected to |
|
| ||
to always disable operation of the infrared sensor on |
|
| ||
the unit by using the following procedure. |
|
| ||
1. Hold down the SURROUND MODE button and | BASIC | CONNECTIONS | ||
| MENU button on the front panel at the same | |||
|
|
| ||
| time for five seconds. |
|
| |
2. The setting “IR=ENABLE” is shown on the FL |
|
| ||
| DISPLAY. |
|
| |
3. Press the 1 or 2 cursor button to change this to |
|
| ||
| “IR=DISABLE”. | OPERATION | ||
4. | Press the ENTER button. Once this setting | |||
|
| |||
| is made, the infrared sensor on the unit is |
|
| |
| disabled. | BASIC | ||
Note: | ||||
|
| |||
| Be sure to set to “IR=ENABLE” when external |
|
| |
| infrared sensors or similar devices are not connected. |
|
| |
| Otherwise, the unit will be unable to receive remote | ADVANCED | CONNECTIONS | |
| control commands. | |||
|
|
| ||
5. To restore the original setting, perform steps 1 |
|
| ||
| to 4 to set to “IR=ENABLE”. |
|
| |
|
| SETUP | ||
|
| ADVANCED | OPERATION | |
|
| TROUBLESHOOTING | ||
|
| OTHERS |
19