Marantz SR4003 manual 1!0o

	ENGLISH
NAMES AND FUNCTIONS	REAR PANEL
	q w	e	r	t	y	u
			INPUT
	VIDEO		1		INPUT
BASIC CONNECTIONS
					3
					COMPONENT
					VIDEO
	S-VIDEO				MONITOR
	FM (75Ω) GND AM				OUT
	ANTENNA		INPUT		INPUT 1	INPUT 2INPUT 3OUTPUT
	TV	DVD VCR IN VCR OUT	DSS MONITOR OUT 2 Y	CB/PB CR/PRY CB/PB	CR/PR
	LSLCSBL				IN
	L
				3	4
	R

uHDMI INPUT/OUTPUT

This unit has 3 HDMI inputs and 1 HDMI output. The input function can be selected from the OSD menu system. (See page 21)

iAC INLET

Plug the supplied power cable into this AC INLET and then into the power outlet on the wall.

This unit can be powered by 120V AC only.

!3AUDIO IN/OUT (CD, TAPE, CD-R, TV, DVD, VCR, DSS)

These are the analog audio inputs and outputs. There are 6 audio inputs (4 of which are linked to video inputs) and 3 audio outputs (1 of which are linked to video outputs). The audio jacks are nominally labeled for cassette tape decks, compact disc players, DVD players and etc.... The audio inputs

and outputs require RCA-type connectors.

R

SR

SW

SBR

IN

OUT

IN

OUT

IN OUT

1

2

OPTOUT

FLASHER

(AUX 2)

7.1CH INPUT

TV DVD

VCR

DSS

TAPE

CD/CDR

DIGITAL IN

DIGITAL OUT REMOTE CONT.

IN

AUDIO

BASIC

L

SL

C

SBL

AC IN

AC OUTLETS

R

L

R

L

R

L

120V 60Hz

OPERATION

FRONT

SURROUND BACK

SURROUND

CENTER

SWITCHED

R

SR

SW

SBR

S. SPEAKER B

1.25A 150W

SPEAKER SYSTEMS : 6-8 OHMS

MODEL NO. SR4003

PRE OUT

ADVANCED CONNECTIONS

!5!4

!3

!2

!1!0o i

q FM antenna terminal (75 ohms)

r

MONITOR OUT

Connect an external FM antenna with a coaxial

This is a monitor output and each one includes both

cable, or a cable network FM source.

composite video and S-video configurations. When

connecting two video monitors or televisions, be

AM antenna and ground terminals

aware that the OSD interface can be used with both

SETUP

MONITOR OUT connections.

Connect the supplied AM loop antenna. Use the

terminals marked “AM” and “GND”. The supplied AM

t

COMPONENT VIDEO INPUT/

loop antenna will provide good AM reception in most

areas. Position the loop antenna until you hear the

OUTPUT

best reception.

If your DVD player or other device has component

ADVANCED OPERATION

video connectors, be sure to connect them to these

w 7.1 CHANNEL or AUX2 INPUT

component video connectors on the unit. This unit

has two component video input connectors to obtain

By connecting a DVD Audio player, Super Audio CD

the color information (Y, CB, CR) directly from the

multichannel player, or other components that has a

recorded DVD signal or other video component and

multichannel port, you can playback the audio with

one component video output connector to output it

TROUBLESHOOTING

5.1 channel or 7.1 channel outputs.

directly into the matrix decoder of the display device.

By sending the pure DVD component video signal

e VIDEO IN/OUT

directly, the DVD signal forgoes the extra processing

(TV, DVD, VCR, DSS)

that normally would degrade the image. The result is

vastly increased image quality, with incredibly life like

These are the video inputs and outputs. There

colors and crisp detail.

are 4 video inputs and 2 video outputs and each

When the video convert function is enabled, video and

one includes both composite video and S-video

S-video images can be output to the COMPONENT

confi gurations. Connect VCRs, DVD players, and

MOINTOR OUT jack.

OTHERS

other video components to the video inputs.

The 2 video output channels can be used to be

y REMOTE CONT. IN/OUT terminals

connected to video tape recorders for making

recordings.

Connect to a Marantz component equipped with

remote control (RC-5) terminals.

oFlasher IN

This terminal controls the unit from each zone. Connect the control signal from a Keypad, etc.

!0AC OUTLETS

Connect the AC power cable of component such as a DVD or CD player to this outlet.

This outlet provides power only when this unit is turned on.

Caution:

•In order to avoid potential turn-off thumps, anything plugged into this outlet should be powered up before this unit is turned on.

•The capacity of this AC outlet is 150W. Do not connect devices that consume electricity more than the capacity of this outlet. If the total power consumption of the connected devices exceeds the capacity, the protection circuit shuts down the power supply.

!1DIGITAL INPUT

These are the digital audio inputs and outputs.

This unit has 2 coaxial digital inputs and 2 optical digital inputs.

The inputs accept digital audio signals from a CD, DVD, or other digital source component.

This unit has 1 optical digital output.

The digital output can be connected to MD recorders, CD recorders, or other similar components.

!2Speaker outputs terminals

Seven terminals are provided for the front left, front right, front center, surround left, surround right, surround back left and surround back right speakers.

Note:

You can use surround back speaker terminals as S (Surround) SPEAKER B terminals, when you use no surround back speaker.

!4Subwoofer Output

Connect this jack to the line level input of a powered subwoofer. If an external subwoofer amplifier is used, connect this jack to the subwoofer amplifier input. If you are using two subwoofers, either powered or with a 2 channel subwoofer amplifier, connect a “Y” connector to the subwoofer output jack and run one cable from it to each subwoofer amplifier.

!5Preamp Outputs

(L, R, SL, SR, SBL, SBR, C)

Jacks for L(front left), R (front right), C (Center), SL (surround left), SR (surround right), SBL (surround back left) and SBR (surround back right).

Use these jacks for connection to external power amplifiers.

8