ENGLISH
NAMESAND FUNCTIONS | CONNECTING SPEAKERS |
|
|
|
|
|
| Powered | Surround | ||
|
|
| BACK |
| |
|
|
| subwoofer |
| |
|
|
| Right | Left | |
|
|
|
| ||
BASIC CONNECTIONS |
| INPUT |
|
|
|
| VIDEO | 1 | INPUT |
|
|
|
|
|
| ||
|
|
| 3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| COMPONENT |
|
|
|
|
|
BASIC |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| VIDEO |
|
|
|
|
|
L |
|
|
|
|
|
|
|
|
|
|
|
|
|
| MONITOR |
|
|
|
|
| ||
| FM (75Ω) | GND | AM |
|
|
|
|
|
|
|
|
|
|
|
|
| OUT |
|
|
|
|
|
| ANTENNA |
|
|
|
|
|
|
| INPUT |
|
|
|
|
|
|
|
| INPUT 1 | INPUT 2 | INPUT 3 | OUTPUT | |
|
|
|
| TV | DVD | VCR IN | VCR OUT | DSS | MONITOR OUT | 2 | Y | CB/PB | CR/PR | Y | CB/PB | CR/PR |
|
|
|
|
|
|
OPERATION | L | SL | C | SBL |
|
|
|
|
|
|
|
|
|
|
|
|
| IN |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 3 | 4 |
|
|
|
|
|
| |
| R |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| R | SR | SW | SBR |
| IN | OUT |
|
| IN | OUT | IN | OUT | 1 | 2 | OPT | OUT | FLASHER |
|
|
| |
|
|
|
|
|
|
|
|
| ||||||||||||||
| (AUX 2) | 7.1CH INPUT | TV | DVD | VCR | DSS |
|
| TAPE |
| CD/CDR | DIGITAL IN | DIGITAL OUT REMOTE CONT. | IN |
|
|
| |||||
|
|
|
|
|
|
|
|
| AUDIO |
|
|
|
|
|
|
|
|
|
|
|
|
|
AC IN
L | SL | C | SBL |
AC OUTLETS
R | L | R | L | R | L | 120V 60Hz |
CONNECTIONS | ADVANCED |
|
|
| FRONT | SURROUND BACK | SURROUND | CENTER | SWITCHED |
|
|
| R | SR | SW | SBR | S. SPEAKER B |
|
| 1.25A 150W |
|
|
|
|
|
|
| SPEAKER SYSTEMS : |
|
| MODEL NO. SR4003 | |
|
|
| PRE OUT |
|
|
|
|
|
|
CONNECTING SPEAKER WIRE
1. Strip away approx. 3/8 inch (10 mm) of wire insulation.
2. Twist the bared wire ends tight, to prevent short circuits.
3. Loosen the knob by turning it counterclockwise.
4. Insert the bare part of the wire into the hole in side of each terminal.
5. Tighten the knob by turning it clockwise to secure the wire.
1.2.
3/8 inch
10mm
3.4. 5.
Caution:
CONNECTING A SUBWOOFER
Use the PRE OUT SUBWOOFER jack to connect a powered subwoofer (power amplifier built in).
SETUP |
|
Right | Left |
Front A | |
ADVANCED OPERATION |
|
TROUBLESHOOTING |
|
OTHERS |
|
Center
Right Left
Surround
•Be sure to use speakers with the specified impedance as shown on the rear panel of this unit.
•To prevent damage
to circuitry, do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit.
•Do not touch the
speaker terminals when the power is on. It may cause you to receive an electric shocks.
•Do not connect more than one speaker cable to one speaker terminal. Doing so may damage this unit.
Note:
Be sure to connect the positive and negative cables for the speaker properly. If they are
10