Marantz SR4003 manual Learn Mode, Learning Procedure, Erasing the code by buttons

LEARN MODE

This remote controller is capable of learning and storing codes used by other remote controls that you already own.

For codes which are not learned, the remote controller will transmit either the Marantz preset codes from the initial settings, or remote codes from another manufacturer’s AV equipment which is set by the customer.

The receiver sensor for the remote controller signals is located at the top of the remote controller.

Notes:

•This remote controller is capable to learn around 60 codes.

•When the batteries are getting weak , the learning procedure is not successful.

LEARNING PROCEDURE

1. Place the remote controller so that its infrared signal transmitter is facing the infrared signal receiver on the Marantz remote controller at a distance of about 0.05 m (2 inches).

4. Select the button to be learned.

• LEARN indicator lights up.

Notes:

•The learning function is unavailable for all SOURCE buttons and HDMI button in any mode.

•The learning function is unavailable for all buttons in TUNER mode and AMP mode.

5.Press and hold the button of the original remote controller to learn until the SEND indicator blinks twice.

Notes:

•When the SEND indicator blinks once, repeat this step.

•If the LEARN indicator flashes when the SEND indicator is lit, then the button cannot be learned.

•When the memory of the remote controller is full, the LEARN and SEND indicators blink once. If you want to learn the code, you should erase other learned button.

6.Repeat steps 4 and 5 to learn other buttons in same SOURCE.

7.Repeat steps 3 to 6 to learn other SOURCE.

8.When you have finished programming the remote controller, press the SET button, then LEARN indicator stops blinking and exits from the LEARN mode.

Notes:

ERASING PROGRAMMED CODES (RETURNING TO INITIAL SETTINGS)

Codes can be erased in three ways: by buttons, sources, and by all memory contents.

Erasing the code by buttons

1. Press and hold down the SET and SETUP buttons until LEARN indicator blinks.

2. Select the SOURCE button to select the button to be erased.

3. Press and hold down the HDMI button and press the learned button twice to be erased.

•SEND indicator blinks twice and the mode returns to LEARN mode.

4. To return the NORMAL mode, press the SET button.

		ENGLISH
3.	Press ENTER button to continue erasing.		NAMES AND	FUNCTIONS
	•	The SEND indicator blinks twice and the
		mode returns to LEARN mode.
	•	To cancel the erasing operation, do not
		press ENTER button and simply touch any
		other button.
4.			BASIC	CONNECTIONS
	To return the NORMAL mode, press the SET		OPERATION
	button.
Erasing the all SOURCES
1.
	Press and hold down the SET and SETUP		BASIC
	buttons until LEARN indicator blinks.
2.	Press and hold down the HDMI button and		ADVANCED	CONNECTIONS
	press POWER ON and POWER OFF button.
	•	LEARN indicator lights.
			SETUP
3.	Press ENTER button to continue erasing.

2. Press and hold down the SET and SETUP buttons until LEARN indicator blinks.

3. Select the SOURCE button to select the

SOURCE.

•When the SEND indicator blinks once again, the transmitting code is unavailable for remote controller, or the transmitting signal is intercepted by noise.

•If no buttons are pressed for approximately 1 minutes while in the LEARN mode, the remote controller automatically exits from the LEARN mode.

Erasing the code by SOURCE

1. Press and hold down the SET and SETUP buttons until LEARN indicator blinks.

2. Press and hold down the HDMI button and press the learned SOURCE button twice to be erased.

• LEARN indicator lights.

•	The SEND indicator blinks twice and the	ADVANCED OPERATION
	mode returns to LEARN mode.
•	To cancel the erasing operation, do not
	press ENTER button and simply touch any
	other button.
4. To return the NORMAL mode, press the SET		TROUBLESHOOTING
button.
Note:		OTHERS

Erasing codes will return to the factory preset code, or there will leave empty if the button has no factory preset code.

35