ENGLISH
NAMESAND FUNCTIONS | SURROUND SPEAKER B SYSTEM | |
The Surround Speaker B system is a function which | ||
| ||
| allows you to listen to the same source in a room other | |
| than the room in which the unit is located. | |
| The operations possible with the Surround speaker | |
BASIC CONNECTIONS | function are explained briefly below. | |
The unit allows you to connect another set of | ||
| ANOTHER ROOM PLAYBACK USING THE | |
| S (SURROUND) SPEAKER B TERMINALS | |
BASIC | speakers and place them in a another room or | |
separated area for listening to music. | ||
OPERATION | ||
1. | ||
ADVANCED CONNECTIONS | ||
2. | ||
| ||
| 1. Press the Z.SPKR button on the remote | |
| controller. The unit enters surround speaker | |
SETUP | B mode and the “SPKR B” will appear on the | |
display. | ||
2. The volume of S. SPEAKER B is interlocked | ||
| with the main volume. | |
| Notes for SURROUND SPEAKER B | |
ADVANCED OPERATION | • SURROUND SPEAKER B On/ Off is available in | |
main room only. | ||
| ||
| • SURROUND SPEAKER B output terminals can be | |
| used when the SURROUND BACK SPEAKER is set | |
| NONE in SPEAKER SETUP menu. (See SPEAKER | |
| SETUP, page 21) | |
TROUBLESHOOTING | • “The Surr. Back Speakers are in use” is displayed | |
the unit is 7.1 CH input mode. | ||
| by pressing the Z. SPKR button on the remote | |
| controller when the SURROUND BACK SPEAKER | |
| is set except NONE in SPEAKER SETUP menu. (See | |
| SPEAKER SETUP, page 21) | |
| • Surround Speaker B function is unavailable, while | |
OTHERS |
|
TUNER OPERATION (PRESET MEMORY)
With this unit you can preset up to 50 FM/AM stations in any order.
For each station, you can memorize the frequency and reception mode if desired.
AUTO PRESET MEMORY
This function automatically scans the FM and AM band and enters all stations with proper signal strength into the memory.
4. 2. 1. 3. 5. 2.
DISP | MULTI | AUTO | TUNED | ST | V – OFF | NIGHT | PEAK | ATT | ANALOG | SURROUND | |
SLEEP | AUTO SURR | DIRECT | DISC 6.1 | MTX 6.1 SPKR B | EQ | DIGITAL | DIGITAL | ||||
|
|
|
|
|
|
|
|
|
| AAC PCM |
|
1. To select FM, press the BAND button on the front panel.
2. While pressing the MEMORY button, press the
2 cursor button.
“AUTO PRESET” will appear on the display, and scanning starts from the lowest frequency.
3. Each time the tuner finds a station, scanning will pause and the station will be played for five seconds.
During this time, the following operations are possible.
The band can be changed by the BAND button.
4. If no button is pressed during this period, the current station is memorized in location Preset 01.
If you wish to skip the current station, press the 3 cursor button during this period, this station is skipped and auto presetting continues.
5. Operation stops automatically when all 50 preset memory positions are fi lled or when auto scanning attains the highest end of all bands. If you desire to stop the auto preset memory at anytime, press the CLEAR button.
Note:
It is possible that existing preset memory positions will be overwritten.
MANUAL PRESET MEMORY
3. 2. 4.
2.
SURROUND
DIGITAL
AAC
3.
(Using the unit)
1. Tune into the radio station you desire (Refer to the “MANUAL TUNING” or “AUTO TUNING” section).
2. Press the MEMORY button on the front panel. “–
3. Select the preset number by pressing the 1 or 2 cursor buttons, while this is still blinking (approx. 5 seconds)
4. Press the MEMORY button again to enter. The display stops blinking.
The station is now stored in the specified preset memory location.
(Using the remote controller)
1. Tune into the radio station you desire (Refer to the “MANUAL TUNING” or “AUTO TUNING” section).
2. Press the MEMO button on the remote controller. “–
3. Enter the desired preset number by pressing the numeric buttons.
Note:
When entering a single digit number (2 for example), either input “02” or just input “2” and wait for a few seconds.
RECALLING A PRESET STATION
1.
1.
SURROUND
DIGITAL
AAC
1.
(Using the unit)
1. Select the desired preset station by pressing the 1 or 2 cursor buttons on the front panel
(Using the remote controller)
1. Press the PRESET + or – buttons to select the desired preset station, or input your desired preset channel with the numeric buttons on the remote controller.
PRESET SCAN
3.
1. 3.
3.
(Using the remote controller)
1. Press the P.SCAN on the remote controller.
“PRESET SCAN” appears on the display and then the preset station with the lowest preset number is recalled first.
2. Preset stations are recalled in sequence (No.1
→No.2 → etc.) for 5 seconds each.
No stored preset number will be skipped.
3. You can fast forward the preset stations by pressing the PRESET + continuously.
When the desired preset station is received, cancel the preset scan operation by pressing the CL button or P.SCAN on the remote controller.
30