ENGLISH
NAMES AND FUNCTIONS | ATTENUATION TO ANALOG INPUT SIGNAL | |
| ||
BASIC CONNECTIONS | If the selected analog audio input signal is greater | |
| ||
| than the capable level of internal processing, the | |
| “PEAK” indicator will light up on the front display. If | |
BASIC | this happens, you should press the ATT button on | |
“ATT” indicator will be illuminated when this function | ||
OPERATION | the remote controller. | |
This function is memorized for each individual input | ||
| is activated. The | |
| about half. Attenuation will not work with the output | |
| signal of | |
ADVANCED CONNECTIONS | source. | |
use of Multi channel Super Audio CD multichannel | ||
| 7.1 CH INPUT | |
| This unit is equipped for future expansion through the | |
| player or | |
| When this is selected, the input signals connected to | |
SETUP | the L(front left), R (front right), CENTER, SL (surround | |
left), SR (surround right) and SBL (surround back left) | ||
| ||
| and SBR (surround back right) channels of the 7.1 | |
| CH. In jacks are output directly to the front (left and | |
| right), center, surround (left and right) and surround | |
| back speaker systems as well as the | |
| without passing through the surround circuitry. | |
ADVANCED OPERATION | In addition, the signal input to the SW (subwoofer) | |
jack is output to the PRE OUT SW (subwoofer) jack. | ||
| ||
| When 7.1 CH. INPUT is selected, the last video input | |
| used remains routed to the Monitor Outputs. | |
| This permits simultaneous viewing with video | |
| sources. | |
TROUBLESHOOTING |
| |
OTHERS |
|
1.4.
SURROUND
DIGITAL
AAC
2. 1.
4.
3.
1. Select a desired Video source to decide the routed video signal to the Monitor Outputs.
2. Press the 7.1 button on the remote controller to switch the 7.1 channel input.
3. If it is necessary to adjust the output level of each channel, press the CH.SEL button on the remote controller.
Adjust the speaker output levels so that you can hear the same sound level from each speaker at the listening position. For the front left, front right, center, surround left, surround right and surround back speakers, the output levels can be adjusted between
The subwoofer can be adjusted between
These adjustments result will be stored to 7.1 CH. INPUT memory.
4. Adjust the main volume with the MAINVOLUME knob or the VOLUME buttons on the remote controller.
To cancel the 7.1 CH. INPUT setting, press 7.1 on the remote controller.
Notes:
•7.1 CH. Input mode bypasses the internal surround processing, so SURROUND mode cannot be selected.
•In addition, there is no signal at the record outputs when the 7.1 CH. Input is in use.
AUX2 INPUT
If you don’t need to connect 7.1 Ch. input terminals with multi channel decoder,
L(front left) and R (front right) inputs terminals are available as AUX2 input.
In this case, You can connect additional audio source to AUX2 as other audio input terminals.
HT-EQ (HOME THEATER EQUALIZER)
1. 2.
At cinemas, the front left, front right and center speakers are located behind the screen. So, screen damping is taken into account when mastering movie software, with an emphasis on high frequencies. When playing back such software at home, the signal takes on different characteristics from those at the cinema. This unit includes
•7.1 CH INPUT
•
•SOURCE DIRECT
•When VIRTUAL is set for the surround mode
1.Press the HT EQ button on the remote controller.
“EQ” indicator on the front panel will illuminate, indicating the HOME THEATER EQUALIZER has been activated.
2.To cancel this function, press the HT EQ button again.
“EQ” indicator on the front panel will be turned off, indicating the HOME THEATER EQUALIZER has been deactivated.
TV AUTO ON/OFF FUNCTION
This function allows the component connected to the
AUTO POWER ON
1. Be sure the TV auto mode is ENABLED. (Refer page 22 : System Setup)
2. Connect your TV TUNER (etc) to the TV- VIDEO in terminal. Be sure to connect the VIDEO input.
3. Turn OFF the power to the TV TUNER and the unit.
4. Turn ON the TV TUNER and tune in a receivable station.
5. When the station is received, this unit turns ON and TV is selected automatically.
AUTO POWER OFF
1. In the above situation, turn the TV TUNER OFF or select a channel that does not contain any broadcast.
2. The power to the unit switches to STANDBY after approx. 5 minutes.
Notes:
•AUTO POWER OFF is canceled if this unit is set to a source other than TV.
The function reactivates when TV is selected again.
•Some TV broadcasts may cause the TV AUTO FUNCTION to turn ON.
•The
28