Linksys WRT54GR manual Back Panel, Network devices

Page 12

Wireless-G Broadband Router with RangeBooster

Chapter 3: Getting to Know the Wireless-G Broadband Router with RangeBooster

The Back Panel

The Router's ports, where the cables are connected, are located on the back panel.

Figure 3-1: The Router’s Back Panel

Reset Button	There are two ways to reset the Router's factory defaults. Either press the Reset Button,
	for approximately five seconds, or restore the defaults from the Administration tab -
	Factory Defaults in the Router's Web-based Utility.
Internet	The Internet port is where you will connect your broadband Internet connection.
Ethernet 1, 2, 3, 4	These ports (1, 2, 3, 4) connect the Router to your networked PCs and other Ethernet
	network devices.

IMPORTANT: Resetting the Router will erase all of your settings (Internet connection, wireless security, and other settings) and replace them with the factory defaults. Do not reset the Router if you want to retain these settings.

Power

The Power port is where you will connect the power adapter.

Chapter 3: Getting to Know the Wireless-G Broadband Router with RangeBooster

6

The Back Panel

Image 12

Contents Wireless- G How to Use This User Guide Copyright and TrademarksWord definition Table of Contents Appendix a Troubleshooting Appendix B Wireless SecurityCommon Problems and Solutions Frequently Asked Questions Appendix C Upgrading Firmware Appendix D Windows HelpList of Figures Router’s Back Panel27 Wireless Tab Wireless MAC Filter Introduction WelcomeWhat’s in this User Guide? Wireless-G Broadband Router with RangeBooster Planning Your Wireless Network Ad-Hoc versus Infrastructure ModeSsid service set identifier your wireless network’s name Network TopologyPlanning Your Wireless Network Network Layout Back Panel Network devicesFront Panel Router’s LEDs are located on the front panelConnecting the Wireless-G Broadband Router with RangeBooster Connecting Your Network Devices Password Screen OverviewSetup Tab Basic Setup Internet SetupPPPoE Connection Type Router IP Time Setting Setup Tab Ddns DDNS.comSetup Tab MAC Address Clone 16 Setup Tab MAC Address CloneSetup Tab Advanced Routing 17 Setup Tab Advanced RoutingWireless Tab Basic Wireless Settings Changes to cancel your changesWireless Tab Wireless Security 20 Wireless Tab Wireless Security WEP22 Wireless Tab Wireless Security PSK2 Radius Wireless Tab Wireless MAC Filter Wireless MAC FilterWireless Tab Advanced Wireless Settings Advanced WirelessWireless-G Broadband Router with RangeBooster Security Tab Firewall FirewallInternet Filter Web FiltersAccess Restrictions Tab Internet Access Policy Internet Access PolicySecurity Tab VPN Passthrough To create an Internet Access policy 33 Internet Policy SummaryApplications and Gaming Tab Single Port Forwarding Single Port ForwardingApplications and Gaming Tab Port Range Forwarding 36 Applications and Gaming Tab Port Range ForwardApplications & Gaming Tab Port Range Triggering Applications and Gaming Tab DMZPort Triggering Range Administration Tab Management ManagementBackup and Restore Administration Tab Log LogAdministration Tab Diagnostics 42 Administration Tab DiagnosticsAdministration Tab Factory Defaults Administration Tab Firmware UpgradeStatus Tab Router Router InformationInternet Connection Status Tab Wireless Network Status Tab Local NetworkAppendix a Troubleshooting Common Problems and SolutionsNeed to set a static IP address on a PC Wireless-G Broadband Router with RangeBooster Open a command prompt. For Windows 98SE and Me Application Start and End Protocol IP Address Enabled TCPCan’t get the Internet game, server, or application to work Wireless-G Broadband Router with RangeBooster To start over, I need to set the Router to factory default Need to upgrade the firmwareFirmware upgrade failed, and/or the Power LED is flashing My DSL service’s PPPoE is always disconnectingPower LED keeps flashing Frequently Asked Questions Where is my SecureEasySetup button?Where is the Router installed on the network? Is IPSec Pass-Through supported by the Router?What is Network Address Translation and what is it used for? Does the Router support ICQ send file?How can I block corrupted FTP downloads? What is DMZ Hosting? What are the advanced features of the Router?What is the Ieee 802.11g standard? Is the Router cross-platform compatible?What is the Ieee 802.11b standard? What Ieee 802.11g features are supported?What Ieee 802.11b features are supported? What is ad-hoc mode?What is ISM band? What is Spread Spectrum?What is DSSS? What is FHSS? And what are their differences? What is WEP? What is a MAC Address?How do I reset the Router? How do I resolve issues with signal loss?Appendix B Wireless Security Security PrecautionsSecurity Threats Facing Wireless Networks Appendix B Wireless Security Wireless-G Broadband Router with RangeBooster Figure C-1 Upgrade Firmware Appendix C Upgrading FirmwareAppendix D Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Windows 98SE or Me Instructions Windows 2000 or XP InstructionsFor the Router’s Web-based Utility Figure E-4 MAC Address Filter ListAppendix D Glossary Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Appendix G Specifications ModelStandards Storage Temp Operating HumidityStorage Humidity Appendix H Warranty Information Limited WarrantyAppendix G Regulatory Information FCC StatementWireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Appendix J Contact Information