Linksys WRT54GR manual Frequently Asked Questions, Where is my SecureEasySetup button?

Page 52

Wireless-G Broadband Router with RangeBooster

Frequently Asked Questions

After using SecureEasySetup, my existing wireless devices can no longer connect to the Router. SecureEasySetup uses WPA-Personal encryption. If your current wireless devices do not support WPA-Personal security, then you cannot use SecureEasySetup on your network. You will need to manually configure your network security using the encryption supported by your existing devices. Re-run the Setup Wizard. On the Welcome screen for the Setup Wizard, click Click Here to Start and follow the on-screen instructions. On the Configure Wireless Settings screen, click Enter Wireless Settings Manually and continue to follow the on- screen instructions. For more information, refer to “Chapter 5: Setting up the Wireless-G Broadband Router with RangeBooster.”

How do I set up additional devices using SecureEasySetup?

Repeat the SecureEasySetup process for each device until all of your devices have been configured.

Where is my SecureEasySetup button?

On the Router, the SecureEasySetup button is located on the front panel. The button should be lighted either orange or white. For other SecureEasySetup devices, refer to each wireless device's documentation to locate the button on that device.

I have devices that support WPA-Personal security, but do not have SecureEasySetup. Can I still use

SecureEasySetup?

Yes. Print out the wireless security settings at the end of the SecureEasySetup process, and then manually configure the settings for your non-SecureEasySetup devices. Refer to each wireless device’s documentation for instructions on how to enter these settings.

What is the maximum number of IP addresses that the Router will support?

The Router will support up to 253 IP addresses.

Is IPSec Pass-Through supported by the Router?

Yes, it is a built-in feature that the Router automatically enables.

Where is the Router installed on the network?

In a typical environment, the Router is installed between the cable/DSL modem and the LAN. Plug the Router into the cable/DSL modem’s Ethernet port.

Does the Router support IPX or AppleTalk?

No. TCP/IP is the only protocol standard for the Internet and has become the global standard for communications. IPX, a NetWare communications protocol used only to route messages from one node to another, and AppleTalk, a communications protocol used on Apple and Macintosh networks, can be used for LAN to LAN connections, but those protocols cannot connect from the Internet to a LAN.

Appendix A: Troubleshooting

46

Frequently Asked Questions

Page 51 Page 53
Image 52
Page 51 Page 53
Contents Wireless- G Copyright and Trademarks How to Use This User GuideWord definition Table of Contents Appendix a Troubleshooting Appendix B Wireless SecurityCommon Problems and Solutions Frequently Asked Questions Appendix C Upgrading Firmware Appendix D Windows HelpList of Figures Router’s Back Panel27 Wireless Tab Wireless MAC Filter Introduction WelcomeWhat’s in this User Guide? Wireless-G Broadband Router with RangeBooster Planning Your Wireless Network Ad-Hoc versus Infrastructure ModeSsid service set identifier your wireless network’s name Network TopologyPlanning Your Wireless Network Network Layout Back Panel Network devicesFront Panel Router’s LEDs are located on the front panelConnecting the Wireless-G Broadband Router with RangeBooster Connecting Your Network Devices Password Screen OverviewSetup Tab Basic Setup Internet SetupPPPoE Connection Type Router IP Time Setting Setup Tab Ddns DDNS.comSetup Tab MAC Address Clone 16 Setup Tab MAC Address CloneSetup Tab Advanced Routing 17 Setup Tab Advanced RoutingWireless Tab Basic Wireless Settings Changes to cancel your changesWireless Tab Wireless Security 20 Wireless Tab Wireless Security WEP22 Wireless Tab Wireless Security PSK2 Radius Wireless Tab Wireless MAC Filter Wireless MAC FilterWireless Tab Advanced Wireless Settings Advanced WirelessWireless-G Broadband Router with RangeBooster Security Tab Firewall FirewallInternet Filter Web FiltersInternet Access Policy Access Restrictions Tab Internet Access PolicySecurity Tab VPN Passthrough To create an Internet Access policy 33 Internet Policy SummaryApplications and Gaming Tab Single Port Forwarding Single Port ForwardingApplications and Gaming Tab Port Range Forwarding 36 Applications and Gaming Tab Port Range ForwardApplications and Gaming Tab DMZ Applications & Gaming Tab Port Range TriggeringPort Triggering Range Administration Tab Management ManagementBackup and Restore Administration Tab Log LogAdministration Tab Diagnostics 42 Administration Tab DiagnosticsAdministration Tab Factory Defaults Administration Tab Firmware UpgradeRouter Information Status Tab RouterInternet Connection Status Tab Wireless Network Status Tab Local NetworkCommon Problems and Solutions Appendix a TroubleshootingNeed to set a static IP address on a PC Wireless-G Broadband Router with RangeBooster Open a command prompt. For Windows 98SE and Me Application Start and End Protocol IP Address Enabled TCPCan’t get the Internet game, server, or application to work Wireless-G Broadband Router with RangeBooster To start over, I need to set the Router to factory default Need to upgrade the firmwareFirmware upgrade failed, and/or the Power LED is flashing My DSL service’s PPPoE is always disconnectingPower LED keeps flashing Frequently Asked Questions Where is my SecureEasySetup button?Where is the Router installed on the network? Is IPSec Pass-Through supported by the Router?What is Network Address Translation and what is it used for? Does the Router support ICQ send file?How can I block corrupted FTP downloads? What is DMZ Hosting? What are the advanced features of the Router?What is the Ieee 802.11g standard? Is the Router cross-platform compatible?What is the Ieee 802.11b standard? What Ieee 802.11g features are supported?What Ieee 802.11b features are supported? What is ad-hoc mode?What is Spread Spectrum? What is ISM band?What is DSSS? What is FHSS? And what are their differences? What is WEP? What is a MAC Address?How do I reset the Router? How do I resolve issues with signal loss?Security Precautions Appendix B Wireless SecuritySecurity Threats Facing Wireless Networks Appendix B Wireless Security Wireless-G Broadband Router with RangeBooster Figure C-1 Upgrade Firmware Appendix C Upgrading FirmwareShared Resources Appendix D Windows HelpNetwork Neighborhood/My Network Places Windows 98SE or Me Instructions Windows 2000 or XP InstructionsFor the Router’s Web-based Utility Figure E-4 MAC Address Filter ListAppendix D Glossary Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Model Appendix G SpecificationsStandards Operating Humidity Storage TempStorage Humidity Appendix H Warranty Information Limited WarrantyAppendix G Regulatory Information FCC StatementWireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Appendix J Contact Information
Top Page Image Contents