Linksys WRT54GR manual Open a command prompt. For Windows 98SE and Me

Page 46

Wireless-G Broadband Router with RangeBooster

BOpen a command prompt. For Windows 98SE and Me:

• Click Start and Run. In the Open field, type command. Press the Enter key or click the OK button. For Windows 2000 and XP:

• Click Start and Run. In the Open field, type cmd. Press the Enter key or click the OK button. In the command prompt, type ping 192.168.1.1 and press the Enter key.

• If you get a reply, the computer is communicating with the Router.

• If you do NOT get a reply, please check the cable, and make sure Obtain an IP address automatically is selected in the TCP/IP settings for your Ethernet adapter.

CIn the command prompt, type ping followed by your Internet or WAN IP address and press the Enter key. The Internet or WAN IP Address can be found on the Status screen of the Router’s web-based utility. For example, if your Internet or WAN IP address is 1.2.3.4, you would enter ping 1.2.3.4 and press the Enter key.

• If you get a reply, the computer is connected to the Router.

• If you do NOT get a reply, try the ping command from a different computer to verify that your original computer is not the cause of the problem.

DIn the command prompt, type ping www.yahoo.com and press the Enter key.

If you get a reply, the computer is connected to the Internet. If you cannot open a webpage, try the ping command from a different computer to verify that your original computer is not the cause of the problem.

If you do NOT get a reply, there may be a problem with the connection. Try the ping command from a different computer to verify that your original computer is not the cause of the problem.

4.I am not getting an IP address on the Internet with my Internet connection.

Refer to “Problem #3, I want to test my Internet connection” to verify that you have connectivity.

If you need to register the MAC address of your Ethernet adapter with your ISP, please see “Appendix E: Finding the MAC address and IP Address for Your Ethernet Adapter.” If you need to clone the MAC address of your Ethernet adapter onto the Router, see the System section of “Chapter 6: Configuring the Wireless-G Broadband Router with RangeBooster” for details.

Make sure you are using the right Internet connection settings. Contact your ISP to see if your Internet connection type is DHCP, Static IP Address, or PPPoE (commonly used by DSL consumers). Please refer to the Setup section of “Chapter 6: Configuring the Wireless-G Broadband Router with RangeBooster” for details on Internet connection settings.

Make sure you have the right cable. Check to see if the Internet column has a solidly lit Link/Act LED.

Make sure the cable connecting from your cable or DSL modem is connected to the Router’s Internet port. Verify that the Status page of the Router’s web-based utility shows a valid IP address from your ISP.

Turn off the computer, Router, and cable/DSL modem. Wait 30 seconds, and then turn on the Router, cable/DSL modem, and computer. Check the Status tab of the Router’s web-based utility to see if you get an IP address.

Appendix A: Troubleshooting

40

Common Problems and Solutions

Image 46
Contents Wireless- G Copyright and Trademarks How to Use This User GuideWord definition Table of Contents Common Problems and Solutions Frequently Asked Questions Appendix a TroubleshootingAppendix B Wireless Security Appendix C Upgrading Firmware Appendix D Windows HelpList of Figures Router’s Back Panel27 Wireless Tab Wireless MAC Filter Introduction WelcomeWhat’s in this User Guide? Wireless-G Broadband Router with RangeBooster Ssid service set identifier your wireless network’s name Planning Your Wireless NetworkAd-Hoc versus Infrastructure Mode Network TopologyPlanning Your Wireless Network Network Layout Back Panel Network devicesFront Panel Router’s LEDs are located on the front panelConnecting the Wireless-G Broadband Router with RangeBooster Connecting Your Network Devices Password Screen OverviewSetup Tab Basic Setup Internet SetupPPPoE Connection Type Router IP Time Setting Setup Tab Ddns DDNS.comSetup Tab MAC Address Clone 16 Setup Tab MAC Address CloneSetup Tab Advanced Routing 17 Setup Tab Advanced RoutingWireless Tab Basic Wireless Settings Changes to cancel your changesWireless Tab Wireless Security 20 Wireless Tab Wireless Security WEP22 Wireless Tab Wireless Security PSK2 Radius Wireless Tab Wireless MAC Filter Wireless MAC FilterWireless Tab Advanced Wireless Settings Advanced WirelessWireless-G Broadband Router with RangeBooster Internet Filter Security Tab FirewallFirewall Web FiltersInternet Access Policy Access Restrictions Tab Internet Access PolicySecurity Tab VPN Passthrough To create an Internet Access policy 33 Internet Policy SummaryApplications and Gaming Tab Single Port Forwarding Single Port ForwardingApplications and Gaming Tab Port Range Forwarding 36 Applications and Gaming Tab Port Range ForwardApplications and Gaming Tab DMZ Applications & Gaming Tab Port Range TriggeringPort Triggering Range Administration Tab Management ManagementBackup and Restore Administration Tab Log LogAdministration Tab Diagnostics 42 Administration Tab DiagnosticsAdministration Tab Factory Defaults Administration Tab Firmware UpgradeRouter Information Status Tab RouterInternet Connection Status Tab Wireless Network Status Tab Local NetworkCommon Problems and Solutions Appendix a TroubleshootingNeed to set a static IP address on a PC Wireless-G Broadband Router with RangeBooster Open a command prompt. For Windows 98SE and Me Application Start and End Protocol IP Address Enabled TCPCan’t get the Internet game, server, or application to work Wireless-G Broadband Router with RangeBooster Firmware upgrade failed, and/or the Power LED is flashing To start over, I need to set the Router to factory defaultNeed to upgrade the firmware My DSL service’s PPPoE is always disconnectingPower LED keeps flashing Where is the Router installed on the network? Frequently Asked QuestionsWhere is my SecureEasySetup button? Is IPSec Pass-Through supported by the Router?What is Network Address Translation and what is it used for? Does the Router support ICQ send file?How can I block corrupted FTP downloads? What is the Ieee 802.11g standard? What is DMZ Hosting?What are the advanced features of the Router? Is the Router cross-platform compatible?What Ieee 802.11b features are supported? What is the Ieee 802.11b standard?What Ieee 802.11g features are supported? What is ad-hoc mode?What is Spread Spectrum? What is ISM band?What is DSSS? What is FHSS? And what are their differences? How do I reset the Router? What is WEP?What is a MAC Address? How do I resolve issues with signal loss?Security Precautions Appendix B Wireless SecuritySecurity Threats Facing Wireless Networks Appendix B Wireless Security Wireless-G Broadband Router with RangeBooster Figure C-1 Upgrade Firmware Appendix C Upgrading FirmwareShared Resources Appendix D Windows HelpNetwork Neighborhood/My Network Places Windows 98SE or Me Instructions Windows 2000 or XP InstructionsFor the Router’s Web-based Utility Figure E-4 MAC Address Filter ListAppendix D Glossary Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Model Appendix G SpecificationsStandards Operating Humidity Storage TempStorage Humidity Appendix H Warranty Information Limited WarrantyAppendix G Regulatory Information FCC StatementWireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Appendix J Contact Information