Linksys WRT54GR manual To start over, I need to set the Router to factory default

Page 50

Wireless-G Broadband Router with RangeBooster

11.To start over, I need to set the Router to factory default.

Hold the Reset button for 10 seconds and then release it. This will return the password, forwarding, and other settings on the Router to the factory default settings. In other words, the Router will revert to its original factory configuration.

12.I need to upgrade the firmware.

In order to upgrade the firmware with the latest features, you need to go to the Linksys website and download the latest firmware at www.linksys.com.

Follow these steps:

1.Go to the Linksys website at http://www.linksys.com and download the latest firmware.

2.To upgrade the firmware, follow the steps in “Appendix C: Upgrading Firmware.”

13.The firmware upgrade failed, and/or the Power LED is flashing.

The upgrade could have failed for a number of reasons. Follow these steps to upgrade the firmware and/or make the Power LED stop flashing:

•If the firmware upgrade failed, use the TFTP program (it was downloaded along with the firmware). Open the pdf that was downloaded along with the firmware and TFTP program, and follow the pdf’s instructions.

•Set a static IP address on the PC; refer to “Problem #2, I need to set a static IP address.” Use the following IP address settings for the computer you are using:

IP Address: 192.168.1.50

Subnet Mask: 255.255.255.0

Gateway: 192.168.1.1

•Perform the upgrade using the TFTP program or the Administration tab of the Router’s web-based utility.

14.My DSL service’s PPPoE is always disconnecting.

PPPoE is not actually a dedicated or always-on connection. The DSL ISP can disconnect the service after a period of inactivity, just like a normal phone dial-up connection to the Internet.

•There is a setup option to “keep alive” the connection. This may not always work, so you may need to re- establish connection periodically.

1.To connect to the Router, go to the web browser, and enter http://192.168.1.1 or the IP address of the Router.

2.Enter the password, if asked. (The default password is admin.)

3.On the Setup screen, select the option Keep Alive, and set the Redial Period option at 20 (seconds).

4.Click the Save Settings button.

5.Click the Status tab, and click the Connect button.

6.You may see the login status display as Connecting. Press the F5 key to refresh the screen, until you see the login status display as Connected.

•Click the Save Settings button to continue.

•If the connection is lost again, follow steps 1- 6 to re-establish connection.

Appendix A: Troubleshooting

44

Common Problems and Solutions

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Wireless- G Word definition How to Use This User GuideCopyright and Trademarks Table of Contents Common Problems and Solutions Frequently Asked Questions Appendix a TroubleshootingAppendix B Wireless Security Appendix C Upgrading Firmware Appendix D Windows HelpList of Figures Router’s Back Panel27 Wireless Tab Wireless MAC Filter Introduction WelcomeWhat’s in this User Guide? Wireless-G Broadband Router with RangeBooster Ssid service set identifier your wireless network’s name Planning Your Wireless NetworkAd-Hoc versus Infrastructure Mode Network TopologyPlanning Your Wireless Network Network Layout Back Panel Network devicesFront Panel Router’s LEDs are located on the front panelConnecting the Wireless-G Broadband Router with RangeBooster Connecting Your Network Devices Password Screen OverviewSetup Tab Basic Setup Internet SetupPPPoE Connection Type Router IP Time Setting Setup Tab Ddns DDNS.comSetup Tab MAC Address Clone 16 Setup Tab MAC Address CloneSetup Tab Advanced Routing 17 Setup Tab Advanced RoutingWireless Tab Basic Wireless Settings Changes to cancel your changesWireless Tab Wireless Security 20 Wireless Tab Wireless Security WEP22 Wireless Tab Wireless Security PSK2 Radius Wireless Tab Wireless MAC Filter Wireless MAC FilterWireless Tab Advanced Wireless Settings Advanced WirelessWireless-G Broadband Router with RangeBooster Internet Filter Security Tab FirewallFirewall Web FiltersSecurity Tab VPN Passthrough Access Restrictions Tab Internet Access PolicyInternet Access Policy To create an Internet Access policy 33 Internet Policy SummaryApplications and Gaming Tab Single Port Forwarding Single Port ForwardingApplications and Gaming Tab Port Range Forwarding 36 Applications and Gaming Tab Port Range ForwardPort Triggering Range Applications & Gaming Tab Port Range TriggeringApplications and Gaming Tab DMZ Administration Tab Management ManagementBackup and Restore Administration Tab Log LogAdministration Tab Diagnostics 42 Administration Tab DiagnosticsAdministration Tab Factory Defaults Administration Tab Firmware UpgradeInternet Connection Status Tab RouterRouter Information Status Tab Wireless Network Status Tab Local NetworkNeed to set a static IP address on a PC Appendix a TroubleshootingCommon Problems and Solutions Wireless-G Broadband Router with RangeBooster Open a command prompt. For Windows 98SE and Me Application Start and End Protocol IP Address Enabled TCPCan’t get the Internet game, server, or application to work Wireless-G Broadband Router with RangeBooster Firmware upgrade failed, and/or the Power LED is flashing To start over, I need to set the Router to factory defaultNeed to upgrade the firmware My DSL service’s PPPoE is always disconnectingPower LED keeps flashing Where is the Router installed on the network? Frequently Asked QuestionsWhere is my SecureEasySetup button? Is IPSec Pass-Through supported by the Router?What is Network Address Translation and what is it used for? Does the Router support ICQ send file?How can I block corrupted FTP downloads? What is the Ieee 802.11g standard? What is DMZ Hosting?What are the advanced features of the Router? Is the Router cross-platform compatible?What Ieee 802.11b features are supported? What is the Ieee 802.11b standard?What Ieee 802.11g features are supported? What is ad-hoc mode?What is DSSS? What is FHSS? And what are their differences? What is ISM band?What is Spread Spectrum? How do I reset the Router? What is WEP?What is a MAC Address? How do I resolve issues with signal loss?Security Threats Facing Wireless Networks Appendix B Wireless SecuritySecurity Precautions Appendix B Wireless Security Wireless-G Broadband Router with RangeBooster Figure C-1 Upgrade Firmware Appendix C Upgrading FirmwareNetwork Neighborhood/My Network Places Appendix D Windows HelpShared Resources Windows 98SE or Me Instructions Windows 2000 or XP InstructionsFor the Router’s Web-based Utility Figure E-4 MAC Address Filter ListAppendix D Glossary Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Standards Appendix G SpecificationsModel Storage Humidity Storage TempOperating Humidity Appendix H Warranty Information Limited WarrantyAppendix G Regulatory Information FCC StatementWireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Wireless-G Broadband Router with RangeBooster Appendix J Contact Information
Top Page Image Contents