Linksys WRH54G manual Connecting Your Network Devices

Page 18

Wireless-G Home Router

9.Decide which network computers or Ethernet devices you want to connect to the Router.

Disconnect the selected computers or devices from the other router, and then connect them to the Router’s numbered ports using standard Ethernet network cabling.

Figure 4-6: Connecting Your Network Devices

10.Connect the AC power adapter to the Router's Power port and the other end into an electrical outlet. Only use the power adapter supplied with the Router. Use of a different adapter may result in product damage.

Figure 4-7: Connecting the Power

Now that the hardware installation is complete, proceed to “Chapter 5: Configuring the Wireless-G Home

Router.”

Chapter 4: Connecting the Wireless-G Home Router

IMPORTANT: Make sure you use the power adapter that is supplied with the Router. Use of a different power adapter could damage the Router.

11

Hardware Installation for Connection to Another Router

Image 18

Contents Wireless- G Copyright and Trademarks Word definitionTable of Contents Appendix a Troubleshooting Appendix B Wireless SecurityAppendix C Upgrading Firmware Appendix D Windows Help List of Figures Router’s Back Panel23 Wireless Tab Wireless Security Radius Figure E-1 IP Configuration Screen Introduction WelcomeWhat’s in this User Guide? Wireless-G Home Router Ssid service set identifier your wireless network’s name Planning Your Wireless NetworkAd-Hoc versus Infrastructure Mode Network TopologyPlanning Your Wireless Network Network Layout Getting to Know the Wireless-G Home Router Back PanelFront Panel Router’s LEDs are located on the front panelConnecting the Wireless-G Home Router OverviewConnecting Your Network Devices Hardware Installation for Connection to Another Router Connecting Another RouterConnecting Your Network Devices Configuring the Wireless-G Home Router Welcome ScreenSetup Tab Basic Setup Internet SetupPPPoE Connection Type Optional Settings Network Setup Time Setting Setup Tab Ddns DdnsSetup Tab MAC Address Clone TZO.comSetup Tab Advanced Routing 15 Setup Tab Advanced Routing RouterSetup Tab WAN Port Configure Wireless Tab Basic Wireless SettingsWireless Tab Wireless Security 19 Wireless Tab Wireless Security WPA Personal22 Wireless Tab Wireless Security WPA2 Enterprise 23 Wireless Tab Wireless Security Radius Wireless Tab MAC Filtering 25 Wireless Tab Wireless MAC FilterWireless Tab Advanced Wireless Settings Severely decrease performanceWireless-G Home Router Security Tab Firewall Additional FiltersSecurity Tab VPN Passthrough Security Tab ARPAccess Restrictions Tab Internet Access 31 Access Restrictions Tab Internet Access34 Port Services Applications and Gaming Tab Single Port Forward 35 Single Port ForwardWireless-G Home Router Applications and Gaming Tab Port Range Forward 36 Applications and Gaming Tab Port Range ForwardApplications & Gaming Tab Port Triggering Triggered RangeApplications and Gaming Tab UPnP 38 Applications and Gaming Tab UPnPApplications and Gaming Tab DMZ 39 Applications and Gaming Tab DMZAdministration Tab Management Administration Tab LogAdministration Tab Diagnostics 43 Administration Tab Diagnostics45 The Traceroute Test Administration Tab Factory Defaults Administration Tab Firmware UpgradeAdministration Tab Config Management Administration Tab Reboot Status Tab RouterStatus Tab Local Network 52 Status Tab Local NetworkStatus Tab Traffic Statistics 54 Traffic StatisticsStatus Tab Wireless 55 Status Tab WirelessAppendix a Troubleshooting Common Problems and SolutionsNeed to set a static IP address on a PC Wireless-G Home Router Open a command prompt. For Windows 98SE and Me Application Start and End Protocol IP Address Enabled Can’t get the Internet game, server, or application to work Wireless-G Home Router Firmware upgrade failed, and/or the Power LED is flashing To start over, I need to set the Router to factory defaultNeed to upgrade the firmware My DSL service’s PPPoE is always disconnectingPower LED keeps flashing Where is the Router installed on the network? Frequently Asked QuestionsWhere is my SecureEasySetup button? Is IPSec Pass-Through supported by the Router?What is Network Address Translation and what is it used for? Does the Router support ICQ send file?How can I block corrupted FTP downloads? What is the Ieee 802.11g standard? What is DMZ Hosting?What are the advanced features of the Router? Is the Router cross-platform compatible?What Ieee 802.11b features are supported? What is the Ieee 802.11b standard?What Ieee 802.11g features are supported? What is ad-hoc mode?What is ISM band? What is Spread Spectrum?What is DSSS? What is FHSS? And what are their differences? How do I reset the Router? What is WEP?What is a MAC Address? How do I resolve issues with signal loss?Appendix B Wireless Security Security PrecautionsSecurity Threats Facing Wireless Networks Appendix B Wireless Security Wireless-G Home Router Figure C-1 Upgrade Firmware Appendix C Upgrading FirmwareAppendix D Windows Help TCP/IPWindows 98SE or Me Instructions Windows 2000 or XP InstructionsFor the Router’s Web-based Utility Figure E-4 MAC Address Filter ListAppendix F Glossary Wireless-G Home Router Wireless-G Home Router Wireless-G Home Router Wireless-G Home Router Appendix G Specifications WRH54GFCC Appendix H Warranty Information Limited WarrantyAppendix I Regulatory Information Wireless-G Home Router Wireless-G Home Router Wireless-G Home Router Wireless-G Home Router Wireless-G Easy Router Appendix J Contact Information