Linksys WRH54G manual To start over, I need to set the Router to factory default

Page 59

Wireless-G Home Router

11.To start over, I need to set the Router to factory default.

Hold the Reset button for 10 seconds and then release it. This will return the password, forwarding, and other settings on the Router to the factory default settings. In other words, the Router will revert to its original factory configuration.

12.I need to upgrade the firmware.

In order to upgrade the firmware with the latest features, you need to go to the Linksys website and download the latest firmware at www.linksys.com.

Follow these steps:

1.Go to the Linksys website at http://www.linksys.com and download the latest firmware.

2.To upgrade the firmware, follow the steps in “Appendix C: Upgrading Firmware.”

13.The firmware upgrade failed, and/or the Power LED is flashing.

The upgrade could have failed for a number of reasons. Follow these steps to upgrade the firmware and/or make the Power LED stop flashing:

•If the firmware upgrade failed, use the TFTP program (it was downloaded along with the firmware). Open the pdf that was downloaded along with the firmware and TFTP program, and follow the pdf’s instructions.

•Set a static IP address on the PC; refer to “Problem #2, I need to set a static IP address.” Use the following IP address settings for the computer you are using:

IP Address: 192.168.1.50

Subnet Mask: 255.255.255.0

Gateway: 192.168.1.1

•Perform the upgrade using the TFTP program or the Administration tab of the Router’s web-based utility.

14.My DSL service’s PPPoE is always disconnecting.

PPPoE is not actually a dedicated or always-on connection. The DSL ISP can disconnect the service after a period of inactivity, just like a normal phone dial-up connection to the Internet.

•There is a setup option to “keep alive” the connection. This may not always work, so you may need to re- establish connection periodically.

1.To connect to the Router, go to the web browser, and enter http://192.168.1.1 or the IP address of the Router.

2.Enter the password, if asked. (The default password is admin.)

3.On the Setup screen, select the option Keep Alive, and set the Redial Period option at 20 (seconds).

4.Click the Save Settings button.

5.Click the Status tab, and click the Connect button.

6.You may see the login status display as Connecting. Press the F5 key to refresh the screen, until you see the login status display as Connected.

•Click the Save Settings button to continue.

•If the connection is lost again, follow steps 1- 6 to re-establish connection.

Appendix A: Troubleshooting

52

Common Problems and Solutions

Page 58 Page 60
Image 59
Page 58 Page 60
Contents Wireless- G Word definition Copyright and TrademarksTable of Contents Appendix C Upgrading Firmware Appendix D Windows Help Appendix a TroubleshootingAppendix B Wireless Security Router’s Back Panel List of Figures23 Wireless Tab Wireless Security Radius Figure E-1 IP Configuration Screen Welcome IntroductionWhat’s in this User Guide? Wireless-G Home Router Network Topology Planning Your Wireless NetworkAd-Hoc versus Infrastructure Mode Ssid service set identifier your wireless network’s namePlanning Your Wireless Network Network Layout Back Panel Getting to Know the Wireless-G Home RouterRouter’s LEDs are located on the front panel Front PanelOverview Connecting the Wireless-G Home RouterConnecting Your Network Devices Connecting Another Router Hardware Installation for Connection to Another RouterConnecting Your Network Devices Welcome Screen Configuring the Wireless-G Home RouterInternet Setup Setup Tab Basic SetupPPPoE Connection Type Optional Settings Network Setup Time Setting Ddns Setup Tab DdnsTZO.com Setup Tab MAC Address Clone15 Setup Tab Advanced Routing Router Setup Tab Advanced RoutingWireless Tab Basic Wireless Settings Setup Tab WAN Port Configure19 Wireless Tab Wireless Security WPA Personal Wireless Tab Wireless Security22 Wireless Tab Wireless Security WPA2 Enterprise 23 Wireless Tab Wireless Security Radius 25 Wireless Tab Wireless MAC Filter Wireless Tab MAC FilteringSeverely decrease performance Wireless Tab Advanced Wireless SettingsWireless-G Home Router Additional Filters Security Tab FirewallSecurity Tab ARP Security Tab VPN Passthrough31 Access Restrictions Tab Internet Access Access Restrictions Tab Internet Access34 Port Services 35 Single Port Forward Applications and Gaming Tab Single Port ForwardWireless-G Home Router 36 Applications and Gaming Tab Port Range Forward Applications and Gaming Tab Port Range ForwardTriggered Range Applications & Gaming Tab Port Triggering38 Applications and Gaming Tab UPnP Applications and Gaming Tab UPnP39 Applications and Gaming Tab DMZ Applications and Gaming Tab DMZAdministration Tab Log Administration Tab Management43 Administration Tab Diagnostics Administration Tab Diagnostics45 The Traceroute Test Administration Tab Config Management Administration Tab Factory DefaultsAdministration Tab Firmware Upgrade Status Tab Router Administration Tab Reboot52 Status Tab Local Network Status Tab Local Network54 Traffic Statistics Status Tab Traffic Statistics55 Status Tab Wireless Status Tab WirelessNeed to set a static IP address on a PC Appendix a TroubleshootingCommon Problems and Solutions Wireless-G Home Router Open a command prompt. For Windows 98SE and Me Application Start and End Protocol IP Address Enabled Can’t get the Internet game, server, or application to work Wireless-G Home Router My DSL service’s PPPoE is always disconnecting To start over, I need to set the Router to factory defaultNeed to upgrade the firmware Firmware upgrade failed, and/or the Power LED is flashingPower LED keeps flashing Is IPSec Pass-Through supported by the Router? Frequently Asked QuestionsWhere is my SecureEasySetup button? Where is the Router installed on the network?Does the Router support ICQ send file? What is Network Address Translation and what is it used for?How can I block corrupted FTP downloads? Is the Router cross-platform compatible? What is DMZ Hosting?What are the advanced features of the Router? What is the Ieee 802.11g standard?What is ad-hoc mode? What is the Ieee 802.11b standard?What Ieee 802.11g features are supported? What Ieee 802.11b features are supported?What is DSSS? What is FHSS? And what are their differences? What is ISM band?What is Spread Spectrum? How do I resolve issues with signal loss? What is WEP?What is a MAC Address? How do I reset the Router?Security Threats Facing Wireless Networks Appendix B Wireless SecuritySecurity Precautions Appendix B Wireless Security Wireless-G Home Router Appendix C Upgrading Firmware Figure C-1 Upgrade FirmwareTCP/IP Appendix D Windows HelpWindows 2000 or XP Instructions Windows 98SE or Me InstructionsFigure E-4 MAC Address Filter List For the Router’s Web-based UtilityAppendix F Glossary Wireless-G Home Router Wireless-G Home Router Wireless-G Home Router Wireless-G Home Router WRH54G Appendix G SpecificationsFCC Limited Warranty Appendix H Warranty InformationAppendix I Regulatory Information Wireless-G Home Router Wireless-G Home Router Wireless-G Home Router Wireless-G Home Router Wireless-G Easy Router Appendix J Contact Information
Top Page Image Contents