Linksys WRH54G manual Frequently Asked Questions, Where is my SecureEasySetup button?

Page 61

Wireless-G Home Router

Frequently Asked Questions

After using SecureEasySetup, my existing wireless devices can no longer connect to the Router. SecureEasySetup uses WPA-Personal encryption. If your current wireless devices do not support WPA-Personal security, then you cannot use SecureEasySetup on your network. You will need to manually configure your network security using the encryption supported by your existing devices. Re-run the Setup Wizard. On the Welcome screen for the Setup Wizard, click Click Here to Start and follow the on-screen instructions. On the Configure Wireless Settings screen, click Enter Wireless Settings Manually and continue to follow the on- screen instructions.

How do I set up additional devices using SecureEasySetup?

Repeat the SecureEasySetup process for each device until all of your devices have been configured.

Where is my SecureEasySetup button?

On the Router, the SecureEasySetup button is located on the front panel. The button should be lighted either orange or white. For other SecureEasySetup devices, refer to each wireless device's documentation to locate the button on that device.

I have devices that support WPA-Personal security, but do not have SecureEasySetup. Can I still use

SecureEasySetup?

Yes. Print out the wireless security settings at the end of the SecureEasySetup process, and then manually configure the settings for your non-SecureEasySetup devices. Refer to each wireless device’s documentation for instructions on how to enter these settings.

What is the maximum number of IP addresses that the Router will support?

The Router will support up to 253 IP addresses.

Is IPSec Pass-Through supported by the Router?

Yes, it is a built-in feature that the Router automatically enables.

Where is the Router installed on the network?

In a typical environment, the Router is installed between the cable/DSL modem and the LAN. Plug the Router into the cable/DSL modem’s Ethernet port.

Does the Router support IPX or AppleTalk?

No. TCP/IP is the only protocol standard for the Internet and has become the global standard for communications. IPX, a NetWare communications protocol used only to route messages from one node to another, and AppleTalk, a communications protocol used on Apple and Macintosh networks, can be used for LAN to LAN connections, but those protocols cannot connect from the Internet to a LAN.

Appendix A: Troubleshooting

54

Frequently Asked Questions

Image 61
Contents Wireless- G Word definition Copyright and TrademarksTable of Contents Appendix B Wireless Security Appendix a TroubleshootingAppendix C Upgrading Firmware Appendix D Windows Help Router’s Back Panel List of Figures23 Wireless Tab Wireless Security Radius Figure E-1 IP Configuration Screen Welcome IntroductionWhat’s in this User Guide? Wireless-G Home Router Ad-Hoc versus Infrastructure Mode Planning Your Wireless NetworkSsid service set identifier your wireless network’s name Network TopologyPlanning Your Wireless Network Network Layout Back Panel Getting to Know the Wireless-G Home RouterRouter’s LEDs are located on the front panel Front PanelOverview Connecting the Wireless-G Home RouterConnecting Your Network Devices Connecting Another Router Hardware Installation for Connection to Another RouterConnecting Your Network Devices Welcome Screen Configuring the Wireless-G Home RouterInternet Setup Setup Tab Basic SetupPPPoE Connection Type Optional Settings Network Setup Time Setting Ddns Setup Tab DdnsTZO.com Setup Tab MAC Address Clone15 Setup Tab Advanced Routing Router Setup Tab Advanced RoutingWireless Tab Basic Wireless Settings Setup Tab WAN Port Configure19 Wireless Tab Wireless Security WPA Personal Wireless Tab Wireless Security22 Wireless Tab Wireless Security WPA2 Enterprise 23 Wireless Tab Wireless Security Radius 25 Wireless Tab Wireless MAC Filter Wireless Tab MAC FilteringSeverely decrease performance Wireless Tab Advanced Wireless SettingsWireless-G Home Router Additional Filters Security Tab FirewallSecurity Tab ARP Security Tab VPN Passthrough31 Access Restrictions Tab Internet Access Access Restrictions Tab Internet Access34 Port Services 35 Single Port Forward Applications and Gaming Tab Single Port ForwardWireless-G Home Router 36 Applications and Gaming Tab Port Range Forward Applications and Gaming Tab Port Range ForwardTriggered Range Applications & Gaming Tab Port Triggering38 Applications and Gaming Tab UPnP Applications and Gaming Tab UPnP39 Applications and Gaming Tab DMZ Applications and Gaming Tab DMZAdministration Tab Log Administration Tab Management43 Administration Tab Diagnostics Administration Tab Diagnostics45 The Traceroute Test Administration Tab Firmware Upgrade Administration Tab Factory DefaultsAdministration Tab Config Management Status Tab Router Administration Tab Reboot52 Status Tab Local Network Status Tab Local Network54 Traffic Statistics Status Tab Traffic Statistics55 Status Tab Wireless Status Tab WirelessCommon Problems and Solutions Appendix a TroubleshootingNeed to set a static IP address on a PC Wireless-G Home Router Open a command prompt. For Windows 98SE and Me Application Start and End Protocol IP Address Enabled Can’t get the Internet game, server, or application to work Wireless-G Home Router Need to upgrade the firmware To start over, I need to set the Router to factory defaultFirmware upgrade failed, and/or the Power LED is flashing My DSL service’s PPPoE is always disconnectingPower LED keeps flashing Where is my SecureEasySetup button? Frequently Asked QuestionsWhere is the Router installed on the network? Is IPSec Pass-Through supported by the Router?Does the Router support ICQ send file? What is Network Address Translation and what is it used for?How can I block corrupted FTP downloads? What are the advanced features of the Router? What is DMZ Hosting?What is the Ieee 802.11g standard? Is the Router cross-platform compatible?What Ieee 802.11g features are supported? What is the Ieee 802.11b standard?What Ieee 802.11b features are supported? What is ad-hoc mode?What is Spread Spectrum? What is ISM band?What is DSSS? What is FHSS? And what are their differences? What is a MAC Address? What is WEP?How do I reset the Router? How do I resolve issues with signal loss?Security Precautions Appendix B Wireless SecuritySecurity Threats Facing Wireless Networks Appendix B Wireless Security Wireless-G Home Router Appendix C Upgrading Firmware Figure C-1 Upgrade FirmwareTCP/IP Appendix D Windows HelpWindows 2000 or XP Instructions Windows 98SE or Me InstructionsFigure E-4 MAC Address Filter List For the Router’s Web-based UtilityAppendix F Glossary Wireless-G Home Router Wireless-G Home Router Wireless-G Home Router Wireless-G Home Router WRH54G Appendix G SpecificationsFCC Limited Warranty Appendix H Warranty InformationAppendix I Regulatory Information Wireless-G Home Router Wireless-G Home Router Wireless-G Home Router Wireless-G Home Router Wireless-G Easy Router Appendix J Contact Information