3Com WL-463, WL-450, WL-462 manual Regulatory Compliance Information

Page 58

REGULATORY COMPLIANCE INFORMATION

3Com Wireless LAN Access Points 8250/8500/8750 (Models WL-450, WL462, WL-463) FCC Radio-Frequency Exposure Notice

This device generates and radiates radio-frequency energy. In order to comply with FCC radio-frequency radiation exposure guidelines for an uncontrolled environment, this equipment has to be installed and operated while maintaining a minimum body to antenna distance of 1 meter.

This product does not contain any user serviceable components. Any unauthorized product changes or modifications will invalidate 3Com’s warranty and all applicable regulatory certifications and approvals. This product must be installed by a professional technician/installer.

FCC Part 15 Notice (Applicable to Use Within the USA)

802.11a radio only: This product is for indoor use only when using channels 36, 40, 44, or 48 (5150–5250 MHz).

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

nReorient or relocate the receiving antenna.

nIncrease the separation between the equipment and receiver.

nConnect the equipment into an outlet on a circuit different from the one which the receiver is connected to. n Consult the dealer or an experienced radio/TV technician for help.

The user may find the following booklet prepared by the Federal Communications Commission helpful: The Interference Handbook

This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402. Stock No. 004-000-00345-4.

Manufacturer’s Declaration of Conformity

3Com Corporation

350 Campus Drive Marlborough, MA 01752-3064 (508) 323-5000

Declares that the product:

Date: 28 February 2003

Brand Name: 3Com Corporation

Model Number: WL-450

Equipment Type: Wireless LAN Access Point

Complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

3Com Corporation WL-450

Tested to Comply with FCC Standards

FOR HOME OR OFFICE USE

Image 58
Contents Wireless LAN Access Points 8250/8500/8750 3Com Corporation 350 Campus Drive Marlborough, MA Contents System Configuration Regulatory Compliance Information Index Product Features IntroductionPerformance and Reliability SecurityManageability FAR-REACHING 802.11G Wireless Network StandardsHIGH-PERFORMANCE 802.11A AD HOC Wireless LAN Network Configuration and PlanningInfrastructure Wireless LAN Infrastructure Wireless LAN for Roaming Wireless PCSTerminology Page Installing the Access Point Installation RequirementsPower Requirements Safety InformationPage Connecting the Standard Antennas Before YOU BeginConnecting Power Using the Power Supply Checking the Leds Using a POWER-OVER-ETHERNET LAN PortMounting on a Wall Plastic anchors and 3 screws Flat Surface Installation Selecting and Connecting a Different Antenna Model Back Power Settings on the Access Point for External Antennas Installing Software UtilitiesPage Using the 3COM Wireless Device Manager Launching a Wireless Device ConfigurationClick Configure Setting the Country Code Configuration LoginUsing the PRE-IP Configuration Wizard Basic Setup Identification Advanced SetupDhcp Client Radius Secure WEB Server ConnectionAuthentication Page Field Default Description Filter Control Filtering by VlanSecurity Filters Client List TimeoutUplink Port MAC Address Filtering Snmp Filtering by Ethernet Protocol TypeAdministration System LOG Status Radio SettingsRadio Interface Page Security Configuring Authentication Configuring EncryptionWPA Configuration WEP Configuration HOW to Setup the Access Point for Radius Authentiction Select Advanced SetupSelect Advanced Setup HOW to Setup the Access Point for WPA with PRE-SHAREDPSK KEYWPA Configuration for Windows XP WEPWPA-PSK AES Troubleshooting Click Configure Client service area to match Where to GO for Help Troubleshoot Online Obtaining Support for Your ProductAccess Software Downloads Contact US Telephone Technical Support and RepairCountry Telephone Number North America Telephone Regulatory Compliance Information Industry Canada IC Emissions Compliance Statement Additional Country Restrictions WL-463, 802.11g Radio Module Safety Compliance Notice Index Radius TCP/IP