Magnavox VRZ242AT owner manual Plug in the TV and the VCR, ANT Audio OUT

Page 7

VRZ242 LAYOUT 4/9/99 9:24 AM Page 7

Hookups Without a Cable Box / Direct Broadcast System (cont’d) 7

3

Connect the RF coaxial cable (supplied) to the OUT Jack on the back of the VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on

type (supplied) or screw-on type of coaxial cable, whichever you prefer.)

Antenna or Cable

ANT

IN

AUDIO

OUT

IN

OUT

VIDEO CH3 CH4

			ANT
			IN
AUDIO
OUT	IN		OUT
VIDEO		CH3	CH4
VIDEO

75V
ANT	/
CABLE

	ANTENNA IN Jack
	(on back of TV)
RF coaxial cable	example only
RF coaxial cable

4

Plug in the TV and the VCR.

5

Set the CH3/CH4 switch on the back of the VCR to CH3 or CH4, whichever channel is not used or least used in your area. Set the TV to the same channel. For example, when playing a tape, if the CH3/CH4 switch is set to CH3, the TV should be on channel 03.

	CH	4
	or	3
	CH	3
	CH

CH3 / CH4

Switch

CH3 CH4

ANT

IN

AUDIO

OUT

IN

OUT

VIDEO CH3 CH4

ANT

IN

AUDIO

OUT

IN

OUT

VIDEO CH3 CH4

6

You are ready to turn on the VCR. Please go to page 11 before turning on the VCR.

Image 7

Contents VRZ242AT For Customer Use Dear Philips Magnavox product ownerSafety Precautions FeaturesIntroduction Table of Contents Before Using Your VCR Disconnect the antenna or cable from your TV Hookups Without a Cable Box / Direct Broadcast SystemANT Audio OUT Plug in the TV and the VCRConnections Hookups With a Cable Box / Direct Broadcast SystemRecording/Viewing Any Channel Recording One Channel/Watching Another Hookups With a Cable Box / Direct Broadcast System cont’dHookups With a Stereo TV 2Turn on the TV Turning on Your VCRPress the VCR button Press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsEnter a 0 before a single digit num- ber Setting the ClockDaylight-Saving Time Language Selection Setting the Remote to Operate a TV 2Find VCR PLUS+/ENTER Button Remote Control ButtonsRemote Control Buttons cont’d If you select Status ON, then select Counter only OFF On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only onVCR Display Panel Front Panel Rear Panel Playing VCR light does not appear, press the VCR/TV button once RecordingRecording One Channel/Watching Another One-Touch Recording Daily Timer RecordingInstructions continue on Timer Recording cont’dTape Speeds Press the STATUS/EXIT button. Program WAS COMSee page 44 for more hints Checking or Cancelling Timer RecordingsChannels Setting Up the VCR Plus+ Programming SystemSetting Up the VCR Plus+ Programming System cont’d Press the VCR PLUS+ /ENTER button Do each step within 60 seconds of the previous stepTimer Recording With the VCR Plus+ Programming System cont’d Antenna Rerecording Tape DuplicationPress the F.FWD/B button so that on appears beside Repeat PlayPress the VCR button Press the Time Search button Time SearchWithin 10 seconds, use the Number buttons to enter Real-Time Counter Memory Viewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPAutomatic Operation Features Helpful Hints Helpful Hints cont’d Cable Box Output Channel 03 or GlossarySpecifications Video Cassette Recorder Limited WarrantyAutomatic IndexVRZ242 Layout 4/9/99 925 AM VRZ242 Layout 4/9/99 925 AM Supplied Accessories