Radio Shack Guide to Using and Programming the Scanner
Page 34

USING THE DISPLAY BACKLIGHT

To turn on the display light for easy viewing at night,

press .The display lights for 15 seconds. To turn off

the light sooner, press again.

USING THE AUTO BACKLIGHT DISPLAY

You can set the scanner so the auto backlight turns on for about 5 seconds when the scanner receives signals.

If you press a key (except ) within 5 seconds, the display remains lighted for more than 15 seconds.

To turn auto backlight display on or off, turn off the scan-

ner. Then hold down and turn on the scanner. on Aut Lit briefly appears when auto backlight is on. OFF Aut Lit briefly appears when auto backlight is off.

CHANGING SEARCH SPEEDS

Note: Hypersearch applies only to the 5 kHz step bands (29–54 MHz, 137–174 MHz, and 216–224.9950 MHz).

The scanner has two search speeds.

Normal Search

Hypersearch

100 steps/second

300 steps/second

To switch between the normal and Hypersearch speeds during limit search or direct search, press H/S. HYPER appears during Hypersearch.

TURNING THE KEYTONE OFF/ON

1.Turn off the scanner.

2.While holding down L-OUT/S/S,turn on the scanner. OFF bEEP appears.

To turn the key tone back on, repeat these steps. on bEEP appears.

34

Special Features

Page 33 Page 35
Image 34
Page 33 Page 35
Contents PRO-94 1000-Channel Handheld Trunking Scanner Contents Special Features Trunking OperationCare and Maintenance Specifications TroubleshootingGeneral Guide to Scanning Features Features Features FCC Notice Frequency Step Range MHz KHz TransmissionScanning Legally Using Non-Rechargeable Batteries Using Internal BatteriesPreparation Preparation11 Using Rechargeable Batteries 12PreparationUsing AC Power Using Vehicle Battery Power Connecting AN EARPHONE/ Headphone Connecting the AntennaConnecting an Optional Antenna Traffic Safety Listening SafelyConnecting AN Extension Speaker Attaching the Belt ClipAbout Your Scanner Look AT the Keypad Key FunctionsNumber Look AT the DisplayKeys About Your Scanner Understanding Banks Service BanksChannel Storage Banks Monitor Memories Operation Turning on the Scanner Setting SquelchStoring Known Frequencies Into Channels Searching for and Temporarily Storing Active Frequencies Limit Search Direct SearchService Bank Search Search Skip Memory Listening to the Monitor Memories Moving a Frequency from a Monitor Memory to a ChannelScanning the Stored Channels Manually Selecting a ChannelDelay Special FeaturesTurning CHANNEL-STORAGE Banks on and OFF Locking OUT Channels PriorityUsing the Keylock Changing Search Speeds Using the Display BacklightUsing the Auto Backlight Display Turning the Keytone OFF/ONSkipping Data Signals Turning the Battery Save Function OFF/ONReceiving NWR-SAME Weather Alert Signals Turning On the Same Weather Alert Feature Same Signal Detection UpdatingNWR-SAME Alert Tone Test NWR-SAME Code Detection TestsTrunking Operation Types of Trunking SystemsSetting the Scanner to the Trunking Mode Simultaneous TrunkingStoring Trunked Frequencies Setting Squelch for the Trunking ModeYou See Trunk System Motorola Type II, VHF frequencies Motorola Type II, 900 MHz frequenciesMotorola Type II, UHF frequencies Searching a Trunked Bank Turning a Trunked Bank On or OffSkipping a Trunked Bank Turning the Status Bit Ignore S-Bit On or OffEdacs Talk Group ID Range Search Identifying a Trunked FrequencySelecting the Edacs Talk Group ID Format Press 0 1 . SRC LimitUsing Hold to Monitor an Active Talk Group ID Locking Out Talk Group IDsUnlocking a Single Talk Group ID Using Trunk Scanning Scan DelayUnlocking All Talk Group IDs Channel Activity Bars Monitoring Talk Group IDsUsing Talk Group ID Lists Manually Storing Talk Group IDs in Talk Group ID ListsYou Press To Scan Entering Edacs Partial Talk GroupsMoving Talk Group IDs to Talk Group ID Lists 01 . EDeleting a Stored Talk Group ID List Scanning the Talk Group ID ListsPriority Talk Group ID Scanning Scanning Type I and Hybrid Trunked Systems E1P1 E1P2 E1P3 E1P4 E1P5 E1P6E1P10 E1P11 E1P12 E1P7 E1P8 E1P9E1P13 E1P14 E1P15 E1P16 Selecting a Preset Fleet MapPress Data ALT Prog then Trunk Programming a Fleet MapSize Code Block Programming the Base Offset Frequencies Programming a Hybrid System Turning On/Off the Motorola Disconnect Tone Detect FunctionNational Weather Frequencies General Guide to ScanningGuide to Frequencies Birdie FrequenciesPrimary Usage Guide to the Action BandsTypical Band Usage VHF BandBand Allocation Abbreviations ServicesUHF Band Aircraft Band- 108-137 MHz VHF Low Band- 29-50 MHz in 5 kHz stepsAmateur Band 50-54 MHz Amateur Band 144-148 MHzGovernment Band 406-420 MHz 406.125-419.975 VHF High Band 148-174 MHzCm Amateur Band 420-450 MHz Conventional Systems Band Locally Assigned Public Safety Band Locally AssignedLow Band 450-470 MHz 856.0125-860.9875Frequency Conversion Problem Possible Cause Remedy TroubleshootingSquelch is not BATT. Lo Troubleshooting67 Resetting the Scanner Care and Maintenance Specifications Search SpeedSquelched 70 mA Limited Ninety-Day Warranty

PRO-94 specifications

The Radio Shack PRO-94 is a versatile and feature-rich handheld scanner that has garnered attention from both amateur radio enthusiasts and professional users alike. Renowned for its accessibility and performance, the PRO-94 serves as an ideal device for those looking to stay connected with various radio frequencies.

One of the main features of the PRO-94 is its ability to receive a wide range of frequencies. The scanner covers VHF low and high bands, UHF, and even the 800 MHz frequency range, allowing users to pick up signals from local police, fire departments, amateur radio operators, and more. This broad frequency range ensures that users can monitor diverse communications and stay informed about local events.

The scanner is equipped with an advanced trunk-tracking technology that allows it to follow trunked radio systems. This is particularly useful for monitoring state and local emergency services, as many of these organizations have migrated to trunked systems to maximize channel efficiency. The PRO-94 simplifies this process by automatically scanning through the trunked frequencies, making it easy for users to catch important dispatches without manual adjustments.

Another standout characteristic of the PRO-94 is its 200 memory channels. Users can program these channels to store specific frequencies, making quick access seamless. The scanner also supports multiple banks, allowing for organized grouping of channels, which is advantageous for users who monitor different types of services or agencies.

With its user-friendly interface, the PRO-94 includes an LCD display that shows relevant information, such as the frequency being received or the bank and channel currently in use. The keypad is designed for efficient navigation, making it straightforward to enter frequency modes and access programmed channels easily. Additionally, the scanner features priority channels, which allow users to monitor certain frequencies continuously, ensuring they do not miss critical communications.

The PRO-94 runs on AA batteries, providing convenience in terms of power supply. Its compact size and lightweight design ensure portability, enabling users to take it on the go, whether on a hiking trip or during community events.

In summary, the Radio Shack PRO-94 stands out as a robust and user-friendly handheld scanner. Its diverse frequency reception, trunk-tracking technology, extensive memory capabilities, and portable design make it a compelling choice for anyone keen on monitoring radio communications.
Top Page Image Contents