Radio Shack PRO-97 manual Assigning a text tag to a group ID, Assigning a text tag to a bank

Page 35

Beyond the Basics

Press 6 then 1.

•A space is entered by pressing ./DELAY.

•“6” is the sixth number associated with 1 on the keypad. Press 1 then 6.

•“m” is the ﬁrst letter associated with 6 on the keypad. Press 6 and FUNC (for the lower case set), then press 1.

5.Press ENT to input the text.

assigning a text tag to a group ID

1.Press PGM.

2.Press TRUNK.

3.Press FUNC then e or d to select the desired bank.

4.Press TRUNK to select the desired sub-bank.

5.Press or hold down e or d to select the desired group ID.

6.Press TEXT then enter the tag using the keypad. (See “Text Input Chart”).

7.Press ENT to store.

assigning a text tag to a bank

1.Press PGM.

2.Press FUNC then press bank number. Bank X (0 through 9) selected. Fn+CLR to delete all frequencies, TEXT to edit tag appears.

3.Press TEXT, then enter the text using the keypad.

4.Press ENT to store.

35

Image 35

Contents PRO-97 1,000 Channel Triple Trunking Hand Held Scanner Contents Contents ﬁnding and storing active frequencies Trunking FCC wants you to know Glossary FAQs Frequently Asked Questions WarrantyCare SpeciﬁcationsYour scanner’s controls ENT completes the entry of frequencies and text TUV enters an 8, or inputs characters T, U, or Basics OFF VOL/SQ turn the scanner on or off and adjust the squelch Using batteries Power sourcesNever install non-rechargeable batteries Charging rechargeable batteries Using AC power Connecting an earphone/headphones Basics Using vehicle battery powerListening safely Connecting an extension speakerTrafﬁc safety Connecting an optional external antenna Basics Connecting the supplied antennaTransferring data to or from another scanner or Basics Using the belt clipUnderstanding your scanner’s modes AM modeQuick start DCS DC mode FM modeCtcss CT mode Motorola mode Basics Edacs mode LTR mode Open and closed modes Basics Turning on the scanner and setting squelch Setting up your scannerBasics Storing known frequencies into channels Beyond the Basics Ctcss and DCS Beyond the Basics DCS Code Table Storing trunking frequencies into channelsAssigning a text tag to a channel Storing text tagsAssigning a text tag to a bank Assigning a text tag to a group IDText input chart Searching a preprogrammed frequency range ﬁnding and storing active frequenciesSearch bank SR0 marine band Band chartsBeyond the Basics Search bank SR2 FRS/GMRS/MURS band Search bank SR1 CB bandSearch bank SR3 police/ﬁre band Search bank SR4 aircraft Search bank SR6 programmable limit search Searching active frequencies in a rangeSearch bank SR5 amateur band Beyond the Basics Listening to the weather band Beyond the Basics Manually tuning a frequencyListening to a weather channel Same standby modeWX Alert and beep tone conﬁrmation Copying a frequency into a speciﬁed channel Using frequency copyBeyond the Basics Skywarn Copying a frequency into an empty channel within a bank Copying a frequency into the priority channel Signal StalkerUsing Signal Stalker II with lockout Using Signal StalkerTurning channel-storage banks off and on Scanning the channelsMonitoring a single channel/power save circuit Using Ctcss and DCSDeleting all frequencies in a channel bank Deleting frequencies from channelsLocking out channels Using delayLocking out channels or frequencies Reviewing locked-out frequencies Reviewing locked-out channelsLocking out frequencies Clearing all locked-out frequencies in a search bank PriorityClearing a locked-out frequency Beyond the Basics Changing the receive mode Using the attenuator Turning the key tone on and off Using the display/key backlightWhile Multi-System Trunking Scanner appears, press Changing the display contrast Beyond the Basics Using the keylockReceives data from another scanner other than a PRO-97 Beyond the Basics Cloning the programmed dataHow trunking works TrunkingTo listen to the transmission, the mode Programming trunking frequencies Beyond the Basics Setting squelch for trunking modeBeyond the Basics Programming Motorola trunking systems UHF-Lo Beyond the Basics Programming ﬂeet maps Programming Motorola trunking systems 800 MHzBlock Size Code S10 S11 S12 Storing talk group IDs Talk group IDsBeyond the Basics Beyond the Basics Turning an ID sub-bank on or off Talk group ID holdLocking out talk group IDs Delay function in ID indication modeClearing all talk group IDs in a single bank Reviewing locked-out talk group IDsClearing talk group IDs Changing the open/closed mode Birdie frequencies Service and repairCare Speciﬁcations Selectivity 25 27.995 MHz at AM mode ±5 kHz 9V DC Beyond the Basics Initializing your scanner Scanning legally FCC wants you to knowGlossary Scanner is not working at all. What’s wrong? FAQs Frequently Asked QuestionsRadioShack Corporation