Radio Shack PRO-97 manual Beyond the Basics Initializing your scanner

Page 84

Beyond the Basics

initializing your scanner

If the scanner’s display locks up or does not work properly after you connect a power source or install batteries, you might need to initialize it.

Notes This procedure clears all information you stored in the scanner’s memory. Initialize the scanner only when you are sure the scanner is not working properly.

1.Turn off the scanner, then turn it on again. Multi-system Trunking Scanner appears.

2.Press 0 while Multi-system Trunking Scanner appears.

3.Press 1.

4.Press ENT. Initializing please stand by. appears for about 5 seconds.

Notes

Do not turn off the scanner until the initalization is complete. When the initialization is complete, M000 appears on the top line of the display. Bank 0 Ch 00 appears on the third line.

84

Image 84

Contents PRO-97 1,000 Channel Triple Trunking Hand Held Scanner Contents Contents ﬁnding and storing active frequencies Trunking Glossary FAQs Frequently Asked Questions Warranty CareSpeciﬁcations FCC wants you to knowYour scanner’s controls ENT completes the entry of frequencies and text TUV enters an 8, or inputs characters T, U, or Basics OFF VOL/SQ turn the scanner on or off and adjust the squelch Power sources Using batteriesNever install non-rechargeable batteries Charging rechargeable batteries Using AC power Basics Using vehicle battery power Connecting an earphone/headphonesConnecting an extension speaker Trafﬁc safetyListening safely Basics Connecting the supplied antenna Connecting an optional external antennaBasics Using the belt clip Transferring data to or from another scanner orAM mode Quick startUnderstanding your scanner’s modes FM mode Ctcss CT modeDCS DC mode Motorola mode Basics Edacs mode LTR mode Open and closed modes Basics Setting up your scanner Turning on the scanner and setting squelchBasics Storing known frequencies into channels Beyond the Basics Ctcss and DCS Beyond the Basics Storing trunking frequencies into channels DCS Code TableStoring text tags Assigning a text tag to a channelAssigning a text tag to a group ID Assigning a text tag to a bankText input chart ﬁnding and storing active frequencies Searching a preprogrammed frequency rangeBand charts Search bank SR0 marine bandBeyond the Basics Search bank SR1 CB band Search bank SR2 FRS/GMRS/MURS bandSearch bank SR3 police/ﬁre band Search bank SR4 aircraft Searching active frequencies in a range Search bank SR5 amateur bandSearch bank SR6 programmable limit search Beyond the Basics Beyond the Basics Manually tuning a frequency Listening to the weather bandSame standby mode Listening to a weather channelWX Alert and beep tone conﬁrmation Using frequency copy Beyond the Basics SkywarnCopying a frequency into a speciﬁed channel Copying a frequency into an empty channel within a bank Signal Stalker Copying a frequency into the priority channelUsing Signal Stalker Using Signal Stalker II with lockoutScanning the channels Turning channel-storage banks off and onUsing Ctcss and DCS Monitoring a single channel/power save circuitDeleting frequencies from channels Deleting all frequencies in a channel bankUsing delay Locking out channels or frequenciesLocking out channels Reviewing locked-out channels Locking out frequenciesReviewing locked-out frequencies Priority Clearing a locked-out frequencyClearing all locked-out frequencies in a search bank Beyond the Basics Changing the receive mode Using the attenuator Using the display/key backlight Turning the key tone on and offWhile Multi-System Trunking Scanner appears, press Beyond the Basics Using the keylock Changing the display contrastBeyond the Basics Cloning the programmed data Receives data from another scanner other than a PRO-97Trunking How trunking worksTo listen to the transmission, the mode Beyond the Basics Setting squelch for trunking mode Programming trunking frequenciesBeyond the Basics Programming Motorola trunking systems UHF-Lo Beyond the Basics Programming Motorola trunking systems 800 MHz Programming ﬂeet mapsBlock Size Code S10 S11 S12 Talk group IDs Storing talk group IDsBeyond the Basics Beyond the Basics Talk group ID hold Turning an ID sub-bank on or offDelay function in ID indication mode Locking out talk group IDsReviewing locked-out talk group IDs Clearing talk group IDsClearing all talk group IDs in a single bank Changing the open/closed mode Service and repair CareBirdie frequencies Speciﬁcations Selectivity 25 27.995 MHz at AM mode ±5 kHz 9V DC Beyond the Basics Initializing your scanner FCC wants you to know Scanning legallyGlossary FAQs Frequently Asked Questions Scanner is not working at all. What’s wrong?RadioShack Corporation