Radio Shack PRO-2096 manual Using attenuator, Fm/Digital

Page 36

Beyond the Basics

To change the receive mode, repeatedly press MODE. The receive mode changes as follows:

AM

configures an AM channel.

FM/DIGITAL

configures an FM/Digital channel.

CT

configures a CTCSS channel.

DC

configures a DCS channel.

MO

configures a MO channel for analog or

 

digital Motorola trunking system channels,

 

or APCO-25 trunking system channels.

ED

configures an ED channel for EDACS

 

trunking system channels.

MO and ED modes are not available when performing service searches, limit searches and the TUNE function.

using attenuator

To reduce interference or noise caused by strong signals, you can reduce the scanner’s sensitivity with the attenuator. There are two attenuator modes in your scanner. Normal attenuator mode allows you to set the attenuator on a per-channel basis. Normal mode is useful when individual channels are found to be prone to interference. Global attenuator mode applies attenuation to every channel in the scanner, and overrides any normal mode attenuator settings that you may have entered.

To assign attenuation to a channel in the scanner, press ATT when the scanner is stopped on a channel, or manually navigate to a channel. A appears on the top of the display. Press ATT again to turn attenuation off.

To assign attenuation to a search bank, press ATT while searching. Attenuation will be applied to the active search bank, or search group within a search bank. Press ATT again to turn attenuation off.

36

Image 36
Contents PRO-2096 Digital Trunking Mobile/Base Scanner Contents Contents Frequency copy Listening to the weather bandVirtual scanner Basics Trunking operation Programming trunked systemsText tags Truobleshooting Resetting/initializing your scanner Glossary WarrantyCare Specifications FCC wants you to knowYour scanner’s keypad See p Your scanner’s rear view Your scanner’s display Install your scanner Mounting your scanner in your dashboardMobile mounting in your vehicle Using your scanner as a base station Use them when you Mount the bracket with ScrewsPower your scanner From a wall outletThrough your vehicle’s ignition From your vehicle’s cigarrette lighter With the metal frame of your vehicleConnect your scanner Connect the supplied antennaConnect an external antenna Connect an external speaker or headphones Listening safelySet up your scanner SquelchStoring conventional frequencies Deleting frequencies from channels Briefly appearsBasics Searching and tuning Basic scanning About channel-storage banksMonitoring a single channel Using Ctcss and DCS Beyond the BasicsSearching a preprogrammed frequency range Search bank charts Receive mode FM/Digital Search bank SR1 CB band Receive mode AM Beyond the Basics Search bank SR4 Aircraft Receive mode AM Using Zeromatic Using seek searchBeyond the Basics Searching for active frequencies Manually tuning to a frequency Frequency copy Copying a frequency into a specified channelCopying a frequency to the priority channel Same standby mode Listening to the weather bandTesting weather alert Using delay Locking out channels/frequenciesLocking out channels Locking out frequencies Reviewing locked-out search frequenciesChanging the receive mode Clearing locked-out search frequenciesClearing locked-out frequencies in search banks Using attenuator FM/DIGITALGlobal attenuator Turning the key tone on or offUsing the dimmer Changing the display contrastVirtual scanner Using V-scanner Save to V-Scanner ENT= Confirm My V-Scanner Loading from Scanner Please Wait While the folder is being cleared, the scanner will display Scanner Operation Complete Press Enter Using digital AGC Cloning programmed dataCloning v-scanner data Turn on both scannersFull cloning Selective cloningBeyond the Basics Beyond the Basics Setting squelch for trunk scanning Trunking operationTalkgroup ID hold Turning an ID sub-bank on or offOpen and closed mode operation Toggling open and closed modes Manual ID lockout toggleTrunked delay function Beyond the Basics Activate ID lockout while scanningReviewing locked-out talkgroup IDs Changing from ID text tag display to ID code displayClearing talkgroups IDs Beyond the Basics Clearing all talkgroup IDs in one bank Programming trunked systems Motorola analog, digital, APCO-25 systemsEdacs systems Motorola VHF and UHF systems Motorola 800MHz splinter systems fleet mapsBlock Size Code S10 S11 S12 Beyond the Basics Programming priority channels Programming the priority channel directlyProgramming a weather channel as the priority channel Turning priority on or offBeyond the Basics Programming CTCSS/DCS channels DCS Code Table Storing talkgroup IDs Clear Text tags Assigning a text tag to a channelAssigning a text tag to a group ID Assigning a text tag to a channel-storage bankBeyond the Basics Text input chart Using channel receive modesUpdating the DSP firmware Troubleshooting Click on Software Updates and DownloadsResetting your scanner Scanner will not scan when Scan is pressedInitializing your scanner InitializingService and repair CareReplacing the fuse Specifications Frequency CoverageIf Rejection Intermediate Frequencies if FCC wants you to know Scanning legallyGlossary Beyond the Basics Beyond the Basics Beyond the Basics Beyond the Basics Beyond the Basics RadioShack Corporation