Radio Shack PRO-2096 manual Cloning v-scanner data, Turn on both scanners

Page 46

Beyond the Basics

CLONE MODE Incorrect Model appears if the scanner receives data from a scanner other than a PRO-2096 and PRO-96. This scanner can send/receive the data to or from a PRO-96 scanner. Only the Light (PRO-96) and Dimmer (PRO-2096) settings are not transferred, they are set to default.

1.Turn on both scanners.

2.Connect the cable to each scanner’s PC/IF jack. *CLONE MODE* UP to send, Remove Cable to Exit appears on the display.

3.Press e or d. Conﬁ rm send data? 1=YES Press other key for NO. appears on the display.

4.Press 1 to send the data to the other unit or press any other key to cancel the operation.

5.The scanner sends the data. Do not disconnect the cable or interrupt power to either scanner while transferring data.

6.To exit clone mode, remove the cable.

cloning v-scanner data

Your scanner supports cloning of both working memory and V-Scanner memory to and from other PRO-2096 and PRO-96 scanners or PC application software. This section describes the process of cloning V-Scanner memory between two radios.

Two types of V-Scanner memory clone are supported. Full Clone transfers all V-Scanner folders from one PRO-2096 (the “source” radio) to a second PRO-2096 or PRO-96 (the “destination” radio). Selective Clone transfers selected V- Scanner folders from a “local” controlling radio to a “remote” slave radio.

Caution

The Full Clone feature should be used with caution – it

overwrites all V-Scanner memory in the destination radio with the contents of the V-Scanner memory in the source

46

Image 46

Contents PRO-2096 Digital Trunking Mobile/Base Scanner Contents Contents Listening to the weather band Frequency copyVirtual scanner Programming trunked systems Basics Trunking operationText tags Care Truobleshooting Resetting/initializing your scannerGlossary Warranty Speciﬁcations FCC wants you to knowYour scanner’s keypad See p Your scanner’s rear view Your scanner’s display Mounting your scanner in your dashboard Install your scannerMobile mounting in your vehicle Using your scanner as a base station Use them when you Mount the bracket with ScrewsFrom a wall outlet Power your scannerThrough your vehicle’s ignition From your vehicle’s cigarrette lighter With the metal frame of your vehicleConnect the supplied antenna Connect your scannerConnect an external antenna Connect an external speaker or headphones Listening safelySquelch Set up your scannerStoring conventional frequencies Deleting frequencies from channels Brieﬂy appearsBasics Searching and tuning About channel-storage banks Basic scanningMonitoring a single channel Beyond the Basics Using Ctcss and DCSSearching a preprogrammed frequency range Search bank charts Receive mode FM/Digital Search bank SR1 CB band Receive mode AM Beyond the Basics Search bank SR4 Aircraft Receive mode AM Using seek search Using ZeromaticBeyond the Basics Searching for active frequencies Manually tuning to a frequency Frequency copy Copying a frequency into a speciﬁed channelCopying a frequency to the priority channel Same standby mode Listening to the weather bandTesting weather alert Locking out channels/frequencies Using delayLocking out channels Locking out frequencies Reviewing locked-out search frequenciesClearing locked-out search frequencies Changing the receive modeClearing locked-out frequencies in search banks Using attenuator FM/DIGITALGlobal attenuator Turning the key tone on or offUsing the dimmer Changing the display contrastVirtual scanner Using V-scanner Save to V-Scanner ENT= Confirm My V-Scanner Loading from Scanner Please Wait While the folder is being cleared, the scanner will display Scanner Operation Complete Press Enter Using digital AGC Cloning programmed dataCloning v-scanner data Turn on both scannersFull cloning Selective cloningBeyond the Basics Beyond the Basics Talkgroup ID hold Setting squelch for trunk scanningTrunking operation Turning an ID sub-bank on or offOpen and closed mode operation Toggling open and closed modes Manual ID lockout toggleReviewing locked-out talkgroup IDs Trunked delay functionBeyond the Basics Activate ID lockout while scanning Changing from ID text tag display to ID code displayClearing talkgroups IDs Beyond the Basics Clearing all talkgroup IDs in one bank Programming trunked systems Motorola analog, digital, APCO-25 systemsEdacs systems Motorola VHF and UHF systems Motorola 800MHz splinter systems ﬂeet mapsBlock Size Code S10 S11 S12 Beyond the Basics Programming priority channels Programming the priority channel directlyProgramming a weather channel as the priority channel Turning priority on or offBeyond the Basics Programming CTCSS/DCS channels DCS Code Table Storing talkgroup IDs Clear Text tags Assigning a text tag to a channelAssigning a text tag to a group ID Assigning a text tag to a channel-storage bankUsing channel receive modes Beyond the Basics Text input chartUpdating the DSP ﬁrmware Troubleshooting Click on Software Updates and DownloadsResetting your scanner Scanner will not scan when Scan is pressedInitializing your scanner InitializingCare Service and repairReplacing the fuse Speciﬁcations Frequency CoverageIf Rejection Intermediate Frequencies if FCC wants you to know Scanning legallyGlossary Beyond the Basics Beyond the Basics Beyond the Basics Beyond the Basics Beyond the Basics RadioShack Corporation