Radio Shack PRO-2096 manual Clearing talkgroups IDs

Page 54

Beyond the Basics

talkgroup before resuming scan operation. Customizing the trunked ID delay may be useful if you are missing a lot of reply traffic on a particular system. We recommend starting with the default value of 2.0 seconds.

1.While in the desired ID list, press FUNC, and then ./DELAY.

2.Press e or d to select None, 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5, or 4.0 seconds.

3.Press ENT.

Most Motorola trunking systems include a “hang time” where the channel remains assigned to a talkgroup for a short period after the user unkeys the microphone.

This hang time is typically 1.5 seconds but can vary among different systems. The scanner’s trunked delay function begins after this hang time expires. Therefore, the total amount of delay present after a user unkeys the microphone equals the trunking system hang time, plus any trunked ID delay programmed into the scanner. For example, if you wish to wait a total of two seconds for a reply trunked call, and the system you are monitoring is using 1.5 seconds of hang time, you should set the trunked delay for that system to 0.5 seconds. EDACS systems do not employ hang time.

Conventional channel delay is fixed at 2 seconds and is controlled independently of trunked ID delay. Refer to “Using Delay” on Page 33 for more information.

clearing talkgroups IDs

You can clear IDs from the ID list to make room for new IDs.

1.Press PROG and then TRUNK.

2.Press FUNC e or d to select an ID memory.

3.Press FUNC and then CLEAR to clear the contents of the selected ID.

54

Image 54
Contents PRO-2096 Digital Trunking Mobile/Base Scanner Contents Contents Frequency copy Listening to the weather bandVirtual scanner Basics Trunking operation Programming trunked systemsText tags Care Truobleshooting Resetting/initializing your scannerGlossary Warranty Specifications FCC wants you to knowYour scanner’s keypad See p Your scanner’s rear view Your scanner’s display Install your scanner Mounting your scanner in your dashboardMobile mounting in your vehicle Using your scanner as a base station Use them when you Mount the bracket with ScrewsPower your scanner From a wall outletThrough your vehicle’s ignition From your vehicle’s cigarrette lighter With the metal frame of your vehicleConnect your scanner Connect the supplied antennaConnect an external antenna Connect an external speaker or headphones Listening safelySet up your scanner SquelchStoring conventional frequencies Deleting frequencies from channels Briefly appearsBasics Searching and tuning Basic scanning About channel-storage banksMonitoring a single channel Using Ctcss and DCS Beyond the BasicsSearching a preprogrammed frequency range Search bank charts Receive mode FM/Digital Search bank SR1 CB band Receive mode AM Beyond the Basics Search bank SR4 Aircraft Receive mode AM Using Zeromatic Using seek searchBeyond the Basics Searching for active frequencies Manually tuning to a frequency Frequency copy Copying a frequency into a specified channelCopying a frequency to the priority channel Same standby mode Listening to the weather bandTesting weather alert Using delay Locking out channels/frequenciesLocking out channels Locking out frequencies Reviewing locked-out search frequenciesChanging the receive mode Clearing locked-out search frequenciesClearing locked-out frequencies in search banks Using attenuator FM/DIGITALGlobal attenuator Turning the key tone on or offUsing the dimmer Changing the display contrastVirtual scanner Using V-scanner Save to V-Scanner ENT= Confirm My V-Scanner Loading from Scanner Please Wait While the folder is being cleared, the scanner will display Scanner Operation Complete Press Enter Using digital AGC Cloning programmed dataCloning v-scanner data Turn on both scannersFull cloning Selective cloningBeyond the Basics Beyond the Basics Talkgroup ID hold Setting squelch for trunk scanningTrunking operation Turning an ID sub-bank on or offOpen and closed mode operation Toggling open and closed modes Manual ID lockout toggleReviewing locked-out talkgroup IDs Trunked delay functionBeyond the Basics Activate ID lockout while scanning Changing from ID text tag display to ID code displayClearing talkgroups IDs Beyond the Basics Clearing all talkgroup IDs in one bank Programming trunked systems Motorola analog, digital, APCO-25 systemsEdacs systems Motorola VHF and UHF systems Motorola 800MHz splinter systems fleet mapsBlock Size Code S10 S11 S12 Beyond the Basics Programming priority channels Programming the priority channel directlyProgramming a weather channel as the priority channel Turning priority on or offBeyond the Basics Programming CTCSS/DCS channels DCS Code Table Storing talkgroup IDs Clear Text tags Assigning a text tag to a channelAssigning a text tag to a group ID Assigning a text tag to a channel-storage bankBeyond the Basics Text input chart Using channel receive modesUpdating the DSP firmware Troubleshooting Click on Software Updates and DownloadsResetting your scanner Scanner will not scan when Scan is pressedInitializing your scanner InitializingService and repair CareReplacing the fuse Specifications Frequency CoverageIf Rejection Intermediate Frequencies if FCC wants you to know Scanning legallyGlossary Beyond the Basics Beyond the Basics Beyond the Basics Beyond the Basics Beyond the Basics RadioShack Corporation