Radio Shack 20-521 owner manual Using AC Power

Page 12

Important: At the end of a rechargeable battery’s use- ful life, it must be recycled or disposed of properly. Contact your local, county, or state hazardous waste management authorities for information on recycling or disposal programs in your area. Some options that might be available are: municipal curb-side collection, drop-off boxes at retailers such as your local Ra- dioShack store, recycling collection centers, and mail- back programs.

Using AC Power

You can power the scanner from a standard AC outlet using an optional AC adapter (such as Cat. No. 273- 1665).

Warning: Do not use an AC adapter’s polarized plug with an extension cord, receptacle, or other outlet un- less the blades can be fully inserted to prevent blade exposure.

Cautions:

•The recommended AC adapter supplies 9 volts and delivers at least 300 milliamps. It has a barrel plug with a center negative tip that correctly fits the scanner’s POWER jack. Using an adapter that does not meet these specifications could damage the scanner or the adapter.

•To protect your scanner and AC adapter, always plug the adapter into the scanner before you plug it into the AC outlet, and always unplug the adapter from the AC outlet before you unplug it from the scanner.

•If batteries are installed, make sure the battery switch inside the battery compartment is set to the correct position (see “Using Internal Batteries” on Page 9).

12

Image 12

Contents PRO-91 150-Channel Handheld Trunking Scanner Features Page Frequency Step Transmission Range MHz KHz FCC Notice Scanning LegallyContents Special Features Trunk TrackingGeneral Guide to Scanning Page Power Sources Using Internal BatteriesPreparation Page Charging Nickel-Cadmium Batteries Using AC Power Using Vehicle Battery Power Plug the adapter’s barrel plug into your scanner’s Connecting the Antenna Connecting an Optional AntennaConnecting AN EARPHONE/ Headphones Traffic SafetyListening Safely Connecting AN Extension Speaker Attaching the Belt ClipAbout Your Scanner Look AT the Keypad Look AT the Display Page Service Banks Understanding BanksChannel Storage Banks Monitor Memories Turning on the Scanner and Setting Squelch OperationStoring Known Frequencies Into Channels Searching for and Temporarily Storing Active Frequencies Limit SearchDirect Search Service Bank Search Search Skip Memory Listening to the Monitor Memories Moving a Frequency from a Monitor Memory to a ChannelScanning the Stored Channels Manually Selecting a ChannelPage Special Features DelayTurning CHANNEL-STORAGE Banks on and OFF Locking OUT Channels PriorityPage Using the Keylock Using the Display BacklightChanging Search Speeds Normal Search HypersearchTurning the Battery Save Function OFF/ON Turning the KEY Tone OFF/ONSkipping Data Signals Trunk Tracking Types of Trunking SystemsSetting the Scanner to the Trunk Tracking Mode Setting Squelch for the Trunk Tracking Mode Storing Trunked FrequenciesPage Scanning a Trunked Bank Monitoring an Active ID Temporarily Storing an ID into the Monitor ID MemoryLocking Out IDs Unlocking a Single IDUnlocking All IDs Using Trunk Tracking Scan Delay Monitoring IDsChannel Activity Bars Scan Lists Manually Storing IDs into Scan ListsMoving IDs to Scan Lists Deleting a Stored IDScanning the Scan Lists Scanning Type I and Hybrid Trunked SystemsProgramming a Fleet Map Size Fleets Subfleets IDs Blocks Used E1P1 E1P2 E1P3 Size E1P4 E1P5 E1P6 Size Selecting a Preset Fleet Map Programming a Hybrid System General Guide to Scanning Guide to FrequenciesNational Weather Frequencies Canadian Weather FrequenciesGuide to the Action Bands Typical Band UsagePrimary Usage VHF BandBand Allocation AbbreviationsVery High Frequency VHF Ultra High Frequency UHF Frequency Conversion Troubleshooting Problem Possible Remedy CauseError Adjust squelch for Resetting the Scanner Care and Maintenance Specifications Power Requirement AA Alkaline Batteries 6.0 VDC Page Page Limited One-Year Warranty RadioShack Division of Tandy Corporation Fort Worth, Texas