Cisco Systems GRP-B manual Gigabit Route Processor Installation and Configuration Note

Page 1

Gigabit Route Processor

Installation and Configuration Note

Product Numbers: GRP-B=, GRP=

Document Order Number: DOC-784339=

This hardware installation and configuration note describes the Gigabit Route Processor (GRP), the route processor for use in Cisco 12000 Series Routers.

Document Contents

Following are the sections in this document:

•Important Information, page 2

•Product Overview, page 3

•Preparing for Installation, page 10

•Replacing a GRP, page 14

•GRP Boot Process Overview, page 24

•Starting the System and Observing Initial Conditions, page 24

•Verifying Interface Status, page 27

•Configuring the Ethernet Interface, page 28

•Implementing Additional Configuration and Maintenance Tasks, page 30

•Obtaining Documentation, page 53

•Documentation Feedback, page 54

•Obtaining Technical Assistance, page 54

•Obtaining Additional Publications and Information, page 55

Corporate Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Copyright © 1997-2002. Cisco Systems, Inc. All rights reserved.

Image 1

Contents Document Contents Gigabit Route Processor Installation and Configuration NoteRouter Information Important InformationSupported Platforms GRP RedundancyCisco IOS Software Requirements Product OverviewRelated Documentation GRP FunctionsCisco IOS Software GRP ComponentsGRP Horizontal Orientation Type Memory ComponentsQuantity Description Location Flash Memory SramSystem Status LEDs Soft Reset SwitchStatus LEDs Display LEDsAsynchronous Serial Ports Flash Card SlotsEthernet Port Safety Guidelines Preparing for InstallationTranslated Safety Warnings and Agency Approvals FCC Class a Compliance Electromagnetic Compatibility Regulatory StatementsCanada Europe EUPreparing for Installation Working with Electrical Equipment Preventing Electrostatic DischargeClass a Notice for Korea Required Tools and Parts Replacing a GRPRemoving a GRP Shows the ejector levers To remove a GRP, follow these steps Turn off system power Installing a GRP Console Port Pin Signal Direction Description Connecting to the Console PortConnecting to the Ethernet Port Connecting to the Auxiliary PortSignal Direction Description Ethernet Interface Receptacles, Cables, and PinoutsRJ-45 Receptacle and Plug Horizontal Orientation Pin DescriptionMII Connections Pin Signal Input Output Input/Output DescriptionRJ-45 Ethernet Interface Cable Connection ProcedureConnecting MII or RJ-45 Cables to GRP Vertical Orientation Starting the System and Observing Initial Conditions GRP Boot Process OverviewLED Display Description ProcessorStarting the System and Observing Initial Conditions Verifying Interface Status GRP LEDs Partial Front Panel View Configuring the Ethernet InterfaceUsing Configuration Mode to Configure the Ethernet Interface Implementing Additional Configuration and Maintenance Tasks Configuring the Software Configuration RegisterBoot Field Description Boot Field Settings and the boot CommandBit Hexadecimal Description Changing Configuration Register Settings Action/File Name Bit Configuration Register Bit MeaningsBaud Bit Bit Address net hostFlash Disks and Flash Memory Cards in the GRP Installing and Removing Flash Memory Card or Flash Disk Formatting a Flash Memory Card or Flash Disk ATA Flash Disk Boot Image Support RequirementsRouter# format slot0 Software Commands Associated with Flash Memory Specifying Cisco IOS Image Used to Boot the SystemRouter# squeeze slot0 Enabling Booting from Flash MemoryRouter# copy tftpmyfile1 slot0myfile1 Copying Files to Flash MemoryRouter# copy tftpnew.image slot0new.image Router# copy slot1image.new slot0image.new Router# config t Routerconfig# no boot system Router# copy startup-config slot0myfile2 Use the copy running-config slot0filename command as follows Recovering Lost Password Initialize the router by entering the i command as follows Locations of GRP Memory Components Upgrading GRP MemoryMEM-GRP/LC-64=2 Removing DIMMs Using Dimm Socket Release Lever to Remove DIMMsHandling a Dimm Installing New DIMMsObtaining Documentation Checking the Dimm InstallationCisco.com Obtaining Technical Assistance Documentation FeedbackOrdering Documentation Cisco TAC WebsiteOpening a TAC Case Obtaining Additional Publications and InformationTAC Case Priority Definitions Obtaining Additional Publications and Information 78-4339-09