Cisco Systems GRP-B manual Pin Description, RJ-45 Receptacle and Plug Horizontal Orientation

Page 20

Replacing a GRP

Figure 6 RJ-45 Receptacle and Plug (Horizontal Orientation)

87654321

RJ-45 receptacle

Category 5, UTP cable with plug

H11096

Warning The ports labeled Ethernet, 10BASE-T, Token Ring, Console, and AUX are safety extra-low voltage (SELV) circuits. SELV circuits should only be connected to other SELV circuits. Because the basic rate interface (BRI) circuits are treated like telephone-network voltage, avoid connecting the SELV circuit to the telephone network voltage (TNV) circuits.

Table 4	RJ-45 Receptacle Pinout

Pin	Description

1	TxD+

2	TxD–

3	RxD+

4	Termination Network

5	Termination Network

6	RxD–

7	Termination Network

8	Termination Network

Depending on your RJ-45 cabling requirements, use the cable pinouts shown in Figure 7 or Figure 8.

Figure 7

MDI wiring

1TxD+

2TxD–

3RxD+

6RxD–

Straight-Through Cable Pinout (Connecting MDI Ethernet Port to MDI-X Wiring)

MDI-X wiring

1 RxD+

2 RxD–

6 TxD–	H11007
3 TxD+

Figure 8

GRP

1TxD+

2TxD–

3RxD+

6RxD–

Crossover Cable Pinout (for Connecting Two GRPs)

GRP

1 TxD+

2 TxD–

6 RxD–	H11006
3 RxD+

Connecting to the Ethernet Port

20	78-4339-09

Image 20

Contents Gigabit Route Processor Installation and Configuration Note Document ContentsImportant Information Router InformationSupported Platforms GRP RedundancyProduct Overview Cisco IOS Software RequirementsRelated Documentation GRP FunctionsGRP Components Cisco IOS SoftwareGRP Horizontal Orientation Quantity Description Location Memory ComponentsType Sram Flash MemorySoft Reset Switch System Status LEDsStatus LEDs Display LEDsEthernet Port Flash Card SlotsAsynchronous Serial Ports Translated Safety Warnings and Agency Approvals Preparing for InstallationSafety Guidelines Electromagnetic Compatibility Regulatory Statements FCC Class a ComplianceCanada Europe EUPreparing for Installation Class a Notice for Korea Preventing Electrostatic DischargeWorking with Electrical Equipment Removing a GRP Replacing a GRPRequired Tools and Parts Shows the ejector levers To remove a GRP, follow these steps Turn off system power Installing a GRP Connecting to the Console Port Console Port Pin Signal Direction DescriptionConnecting to the Auxiliary Port Connecting to the Ethernet PortSignal Direction Description Ethernet Interface Receptacles, Cables, and PinoutsPin Description RJ-45 Receptacle and Plug Horizontal OrientationPin Signal Input Output Input/Output Description MII ConnectionsEthernet Interface Cable Connection Procedure RJ-45Connecting MII or RJ-45 Cables to GRP Vertical Orientation GRP Boot Process Overview Starting the System and Observing Initial ConditionsProcessor LED Display DescriptionStarting the System and Observing Initial Conditions Verifying Interface Status Configuring the Ethernet Interface GRP LEDs Partial Front Panel ViewUsing Configuration Mode to Configure the Ethernet Interface Configuring the Software Configuration Register Implementing Additional Configuration and Maintenance TasksBit Hexadecimal Description Boot Field Settings and the boot CommandBoot Field Description Changing Configuration Register Settings Configuration Register Bit Meanings Action/File Name BitBit Address net host Baud BitFlash Disks and Flash Memory Cards in the GRP Installing and Removing Flash Memory Card or Flash Disk ATA Flash Disk Boot Image Support Requirements Formatting a Flash Memory Card or Flash DiskRouter# format slot0 Specifying Cisco IOS Image Used to Boot the System Software Commands Associated with Flash MemoryEnabling Booting from Flash Memory Router# squeeze slot0Copying Files to Flash Memory Router# copy tftpmyfile1 slot0myfile1Router# copy tftpnew.image slot0new.image Router# copy slot1image.new slot0image.new Router# config t Routerconfig# no boot system Router# copy startup-config slot0myfile2 Use the copy running-config slot0filename command as follows Recovering Lost Password Initialize the router by entering the i command as follows Upgrading GRP Memory Locations of GRP Memory ComponentsMEM-GRP/LC-64=2 Using Dimm Socket Release Lever to Remove DIMMs Removing DIMMsInstalling New DIMMs Handling a DimmCisco.com Checking the Dimm InstallationObtaining Documentation Documentation Feedback Obtaining Technical AssistanceOrdering Documentation Cisco TAC WebsiteTAC Case Priority Definitions Obtaining Additional Publications and InformationOpening a TAC Case Obtaining Additional Publications and Information 78-4339-09