Cisco Systems GRP-B Documentation Feedback, Obtaining Technical Assistance, Cisco TAC Website

Page 54

Documentation Feedback

You can access the Cisco website at this URL:

http://www.cisco.com

International Cisco websites can be accessed from this URL:

http://www.cisco.com/public/countries_languages.shtml

Ordering Documentation

You can find instructions for ordering documentation at this URL:

http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm

You can order Cisco documentation in these ways:

•Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Networking Products MarketPlace:

http://www.cisco.com/en/US/partner/ordering/index.shtml

•Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in North America, by calling 800 553-NETS (6387).

Documentation Feedback

You can submit e-mail comments about technical documentation to bug-doc@cisco.com.

You can submit comments by using the response card (if present) behind the front cover of your document or by writing to the following address:

Cisco Systems

Attn: Customer Document Ordering

170 West Tasman Drive

San Jose, CA 95134-9883

We appreciate your comments.

Obtaining Technical Assistance

For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, the Cisco Technical Assistance Center (TAC) provides 24-hour-a-day, award-winning technical support services, online and over the phone. Cisco.com features the Cisco TAC website as an online starting point for technical assistance. If you do not hold a valid Cisco service contract, please contact your reseller.

Cisco TAC Website

The Cisco TAC website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The Cisco TAC website is available 24 hours a day, 365 days a year. The Cisco TAC website is located at this URL:

http://www.cisco.com/tac

Ordering Documentation

54	78-4339-09

Image 54

Contents Gigabit Route Processor Installation and Configuration Note Document ContentsSupported Platforms Important InformationRouter Information GRP RedundancyRelated Documentation Product OverviewCisco IOS Software Requirements GRP FunctionsGRP Components Cisco IOS SoftwareGRP Horizontal Orientation Memory Components TypeQuantity Description Location Sram Flash MemoryStatus LEDs Soft Reset SwitchSystem Status LEDs Display LEDsFlash Card Slots Asynchronous Serial PortsEthernet Port Preparing for Installation Safety GuidelinesTranslated Safety Warnings and Agency Approvals Canada Electromagnetic Compatibility Regulatory StatementsFCC Class a Compliance Europe EUPreparing for Installation Preventing Electrostatic Discharge Working with Electrical EquipmentClass a Notice for Korea Replacing a GRP Required Tools and PartsRemoving a GRP Shows the ejector levers To remove a GRP, follow these steps Turn off system power Installing a GRP Connecting to the Console Port Console Port Pin Signal Direction DescriptionSignal Direction Description Connecting to the Auxiliary PortConnecting to the Ethernet Port Ethernet Interface Receptacles, Cables, and PinoutsPin Description RJ-45 Receptacle and Plug Horizontal OrientationPin Signal Input Output Input/Output Description MII ConnectionsEthernet Interface Cable Connection Procedure RJ-45Connecting MII or RJ-45 Cables to GRP Vertical Orientation GRP Boot Process Overview Starting the System and Observing Initial ConditionsProcessor LED Display DescriptionStarting the System and Observing Initial Conditions Verifying Interface Status Configuring the Ethernet Interface GRP LEDs Partial Front Panel ViewUsing Configuration Mode to Configure the Ethernet Interface Configuring the Software Configuration Register Implementing Additional Configuration and Maintenance TasksBoot Field Settings and the boot Command Boot Field DescriptionBit Hexadecimal Description Changing Configuration Register Settings Configuration Register Bit Meanings Action/File Name BitBit Address net host Baud BitFlash Disks and Flash Memory Cards in the GRP Installing and Removing Flash Memory Card or Flash Disk ATA Flash Disk Boot Image Support Requirements Formatting a Flash Memory Card or Flash DiskRouter# format slot0 Specifying Cisco IOS Image Used to Boot the System Software Commands Associated with Flash MemoryEnabling Booting from Flash Memory Router# squeeze slot0Copying Files to Flash Memory Router# copy tftpmyfile1 slot0myfile1Router# copy tftpnew.image slot0new.image Router# copy slot1image.new slot0image.new Router# config t Routerconfig# no boot system Router# copy startup-config slot0myfile2 Use the copy running-config slot0filename command as follows Recovering Lost Password Initialize the router by entering the i command as follows Upgrading GRP Memory Locations of GRP Memory ComponentsMEM-GRP/LC-64=2 Using Dimm Socket Release Lever to Remove DIMMs Removing DIMMsInstalling New DIMMs Handling a DimmChecking the Dimm Installation Obtaining DocumentationCisco.com Ordering Documentation Documentation FeedbackObtaining Technical Assistance Cisco TAC WebsiteObtaining Additional Publications and Information Opening a TAC CaseTAC Case Priority Definitions Obtaining Additional Publications and Information 78-4339-09