Cisco Systems GRP Electromagnetic Compatibility Regulatory Statements, FCC Class a Compliance

Page 11

Preparing for Installation

Electromagnetic Compatibility Regulatory Statements

FCC Class A Compliance

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

Modifying the equipment without Cisco’s authorization may result in the equipment no longer complying with FCC requirements for Class A digital devices. In that event, your right to use the equipment may be limited by FCC regulation and you may be required to correct any interference to radio or television communication at your own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:

•Turn the television or radio antenna until the interference stops.

•Move the equipment to one side or the other of the television or radio.

•Move the equipment farther away from the television or radio.

•Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.)

CISPR 22

This apparatus complies with EN55022 Class B radiated and conducted emissions requirements.

Canada

English Statement of Compliance

This class A digital apparatus complies with Canadian ICES-003.

French Statement of Compliance

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Europe (EU)

This apparatus complies with EN55022 Class A and EN55024 standards when used as ITE/TTE equipment, and EN 300 386-2 (EN55022 class B with shielded CAT5 Ethernet cable, non-central office equipment) for Telecommunications Network Equipment (TNE).

Electromagnetic Compatibility Regulatory Statements

 

78-4339-09

11

 

 

 

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Document Contents Gigabit Route Processor Installation and Configuration NoteGRP Redundancy Important InformationRouter Information Supported PlatformsGRP Functions Product OverviewCisco IOS Software Requirements Related DocumentationCisco IOS Software GRP ComponentsGRP Horizontal Orientation Quantity Description Location Memory ComponentsType Flash Memory SramDisplay LEDs Soft Reset SwitchSystem Status LEDs Status LEDsEthernet Port Flash Card SlotsAsynchronous Serial Ports Translated Safety Warnings and Agency Approvals Preparing for InstallationSafety Guidelines Europe EU Electromagnetic Compatibility Regulatory StatementsFCC Class a Compliance CanadaPreparing for Installation Class a Notice for Korea Preventing Electrostatic DischargeWorking with Electrical Equipment Removing a GRP Replacing a GRPRequired Tools and Parts Shows the ejector levers To remove a GRP, follow these steps Turn off system power Installing a GRP Console Port Pin Signal Direction Description Connecting to the Console PortEthernet Interface Receptacles, Cables, and Pinouts Connecting to the Auxiliary PortConnecting to the Ethernet Port Signal Direction DescriptionRJ-45 Receptacle and Plug Horizontal Orientation Pin DescriptionMII Connections Pin Signal Input Output Input/Output DescriptionRJ-45 Ethernet Interface Cable Connection ProcedureConnecting MII or RJ-45 Cables to GRP Vertical Orientation Starting the System and Observing Initial Conditions GRP Boot Process OverviewLED Display Description ProcessorStarting the System and Observing Initial Conditions Verifying Interface Status GRP LEDs Partial Front Panel View Configuring the Ethernet InterfaceUsing Configuration Mode to Configure the Ethernet Interface Implementing Additional Configuration and Maintenance Tasks Configuring the Software Configuration RegisterBit Hexadecimal Description Boot Field Settings and the boot CommandBoot Field Description Changing Configuration Register Settings Action/File Name Bit Configuration Register Bit MeaningsBaud Bit Bit Address net hostFlash Disks and Flash Memory Cards in the GRP Installing and Removing Flash Memory Card or Flash Disk Formatting a Flash Memory Card or Flash Disk ATA Flash Disk Boot Image Support RequirementsRouter# format slot0 Software Commands Associated with Flash Memory Specifying Cisco IOS Image Used to Boot the SystemRouter# squeeze slot0 Enabling Booting from Flash MemoryRouter# copy tftpmyfile1 slot0myfile1 Copying Files to Flash MemoryRouter# copy tftpnew.image slot0new.image Router# copy slot1image.new slot0image.new Router# config t Routerconfig# no boot system Router# copy startup-config slot0myfile2 Use the copy running-config slot0filename command as follows Recovering Lost Password Initialize the router by entering the i command as follows Locations of GRP Memory Components Upgrading GRP MemoryMEM-GRP/LC-64=2 Removing DIMMs Using Dimm Socket Release Lever to Remove DIMMsHandling a Dimm Installing New DIMMsCisco.com Checking the Dimm InstallationObtaining Documentation Cisco TAC Website Documentation FeedbackObtaining Technical Assistance Ordering DocumentationTAC Case Priority Definitions Obtaining Additional Publications and InformationOpening a TAC Case Obtaining Additional Publications and Information 78-4339-09
Top Page Image Contents