Cisco Systems GRP-B manual Preparing for Installation, Safety Guidelines

Page 10

Preparing for Installation

Preparing for Installation

Installation preparation is presented in the following sections:

•Safety Guidelines

•Translated Safety Warnings and Agency Approvals

•Electromagnetic Compatibility Regulatory Statements

•Preventing Electrostatic Discharge

•Working with Electrical Equipment

•Required Tools and Parts

Safety Guidelines

Before you perform any procedure in this publication, review the safety guidelines in this section to avoid injuring yourself or damaging the equipment.

The following guidelines are for your safety and to protect the equipment. The guidelines do not include all hazards. Be alert.

Note Review the safety warnings listed in the Regulatory Compliance and Safety Information for Cisco 12000 Series Internet Routers publication (Document Number 78-4347-xx) for your router before installing, configuring, or maintaining the GRP.

•Keep the work area clear and dust free during and after installation. Do not allow dirt or debris to enter into any components.

•Do not wear loose clothing, jewelry, or other items that could get caught in the router while working with the GRP.

•The GRP operates safely when it is used in accordance with its specifications and product usage instructions.

•Review all safety and ESD-prevention guidelines to help you to avoid injury or damage to the equipment.

•Ensure that your equipment configuration meets the minimum requirements for the upgrade or replacement you will perform and that you have all the parts and tools you need.

•If you plan to replace a GRP, back up your current configuration file to a remote server or to Flash memory before you remove the GRP. This prevents you from having to reenter all your current configuration information manually. To back up the file, copy your configuration file to a Flash disk or access a remote server.

Translated Safety Warnings and Agency Approvals

The complete list of safety warnings and agency approvals for the PRP is available in the Regulatory Compliance and Safety Information for Cisco 12000 Series Internet Routers publication (Document Number 78-4347-xx).

Preparing for Installation

10	78-4339-09

Image 10

Contents Gigabit Route Processor Installation and Configuration Note Document ContentsSupported Platforms Important InformationRouter Information GRP RedundancyRelated Documentation Product OverviewCisco IOS Software Requirements GRP FunctionsGRP Components Cisco IOS SoftwareGRP Horizontal Orientation Type Memory ComponentsQuantity Description Location Sram Flash MemoryStatus LEDs Soft Reset SwitchSystem Status LEDs Display LEDsAsynchronous Serial Ports Flash Card SlotsEthernet Port Safety Guidelines Preparing for InstallationTranslated Safety Warnings and Agency Approvals Canada Electromagnetic Compatibility Regulatory StatementsFCC Class a Compliance Europe EUPreparing for Installation Working with Electrical Equipment Preventing Electrostatic DischargeClass a Notice for Korea Required Tools and Parts Replacing a GRPRemoving a GRP Shows the ejector levers To remove a GRP, follow these steps Turn off system power Installing a GRP Connecting to the Console Port Console Port Pin Signal Direction DescriptionSignal Direction Description Connecting to the Auxiliary PortConnecting to the Ethernet Port Ethernet Interface Receptacles, Cables, and PinoutsPin Description RJ-45 Receptacle and Plug Horizontal OrientationPin Signal Input Output Input/Output Description MII ConnectionsEthernet Interface Cable Connection Procedure RJ-45Connecting MII or RJ-45 Cables to GRP Vertical Orientation GRP Boot Process Overview Starting the System and Observing Initial ConditionsProcessor LED Display DescriptionStarting the System and Observing Initial Conditions Verifying Interface Status Configuring the Ethernet Interface GRP LEDs Partial Front Panel ViewUsing Configuration Mode to Configure the Ethernet Interface Configuring the Software Configuration Register Implementing Additional Configuration and Maintenance TasksBoot Field Description Boot Field Settings and the boot CommandBit Hexadecimal Description Changing Configuration Register Settings Configuration Register Bit Meanings Action/File Name BitBit Address net host Baud BitFlash Disks and Flash Memory Cards in the GRP Installing and Removing Flash Memory Card or Flash Disk ATA Flash Disk Boot Image Support Requirements Formatting a Flash Memory Card or Flash DiskRouter# format slot0 Specifying Cisco IOS Image Used to Boot the System Software Commands Associated with Flash MemoryEnabling Booting from Flash Memory Router# squeeze slot0Copying Files to Flash Memory Router# copy tftpmyfile1 slot0myfile1Router# copy tftpnew.image slot0new.image Router# copy slot1image.new slot0image.new Router# config t Routerconfig# no boot system Router# copy startup-config slot0myfile2 Use the copy running-config slot0filename command as follows Recovering Lost Password Initialize the router by entering the i command as follows Upgrading GRP Memory Locations of GRP Memory ComponentsMEM-GRP/LC-64=2 Using Dimm Socket Release Lever to Remove DIMMs Removing DIMMsInstalling New DIMMs Handling a DimmObtaining Documentation Checking the Dimm InstallationCisco.com Ordering Documentation Documentation FeedbackObtaining Technical Assistance Cisco TAC WebsiteOpening a TAC Case Obtaining Additional Publications and InformationTAC Case Priority Definitions Obtaining Additional Publications and Information 78-4339-09