Acnodes PC 6170 manual Touch Screen, Specification

Page 34

PC 6170 User’s Manual

3.2Touch Screen

3.2.1 Specification

Touch Screen:

For 8-wire analog resistive type

Touch Screen Controller:

DMC9000

Communications:

RS-232

Baud Rate:

19200 baud rate fixed

Resolution:

1024 x 1024 (10-bit A/D converter inside)

Power Input:

5V to 12V DC

Power Consumption:

12V: 27mA+ i where (i = v/touch screen sheet R)

 

5V: 23mA+ i where (i = v/touch screen sheet R)

Board Size:

6.0 x 2.0 cm

Portrait:

Support 90o to 270o screen rotation

Static Protection:

ESD device option

 

 

Others:

Touch activate indication LED on board

26

Driver Installation

Page 33 Page 35
Image 34
Page 33 Page 35
Contents
Pentium-M Panel PC Disclaimers Safety Approvals FCC ComplianceSafety Precautions Trademarks Acknowledgments This page does not contain any information Table of Contents Embedded O.S. Installation General Description Front Access USB Ports & OSDIntroduction Most Reliable and Stable Design-Intel Pentium M ProcessorEasy-to-Maintenance Design Back Door SpecificationsMain CPU board System „ Standard I/OSystem Specification „ 17 TFT LCD „ Disk drive housingDimensions Front View and I/O Outlets Front View2 I/O Outlet VGAPackage list Hardware Installation CPU and Dram InstallationDram CPU HDD Installation User’s Manual CD-ROM Installation Put the CD-ROM in the drive bracket and fix it by 6 screws Add-on Card Installation Parallel Port 3 x Serial PortsVGA RJ-45 Connector Pin Assignment EthernetMountings Panel/Wall/Desktop/VESA/Rack VESA-ARMWall Mount PC 6170 User’s Manual Desktop Kit Assembly Fix two holders by 2 screws Complete Panel-mount Kit Assembly Rack mounting Assembly Driver Installation SystemSpecification Touch ScreenDriver Installation- Windows 98/2000/XP/CE.NET/XP-Embedded PC 6170 User’s Manual Driver Installation- DOS Identify the communication port and IRQ numberDo Calibration Driver Installation- Linux Install PenMount driverSet COM3 as touch Dual LAN This page does not contain any information Windows XP Embedded Embedded O.S. InstallationPenmount Touch Screen Windows CE.NET Calibration Touch ScreenSBC83810 Bios Setup Standard Cmos Setup MenuDate TimeDrive a type/Drive B type Halt OnAdvanced Bios Features ScsiVirus Warning Hard Disk Boot PriorityQuick Power On Self Test CPU L1 & L2 CacheBoot Up Floppy Seek First/Second/Third Boot DeviceBoot Other Device Boot Up NumLock StatusTypematic Delay Msec Typematic Rate SettingTypematic Rate Chars/Sec OS Select for Dram 64MB Security OptionReport No FDD For Win Dram Data Integrity Mode Advanced Chipset FeaturesSdram CAS latency Time Delayed Transaction System Bios CacheableVideo Bios Cacheable Video RAM CacheableIntegrated Peripherals SPP IDE Primary/Secondary Master/Slave PIO IDE HDD Block ModePower on Function IDE Primary/Secondary Master/Slave UdmaOnboard FDC Controller UART2 Duplex ModeParallel Port Mode Onboard Serial Port 1/PortECP Mode Use DMA Power Management Setup S1POSPM Control by APM Power ManagementAcpi Function Video Off MethodSuspend Mode Doze ModeStandby Mode Video Off AfterThrottle Duty Cycle HDD Power DownPower On by Ring VGA Active MonitorReload Global Timer Events PNP OS Installed PnP/PCI Configuration SetupReset Configuration Data DMA Resources Resources Controlled ByIRQ Resources Memory ResourcesPC Health Status Current CPU TemperatureCurrent FAN1/FAN2 Speed Auto Detect DIMM/PCI Clk Frequency/Voltage ControlSpeed Spectrum Load Fail-Safe Defaults Cmos Setup Utility-Copyright Award SoftwareLoad Optimized Defaults Load Optimized Defaults Y/N? NPower Supply Specification Power Supply FSP180-50PLA1 180W, AC 110~230V InputHOLD-UP Time @FULL Load Short Circuit Protection Efficiency Shock
Top Page Image Contents