Acnodes PC 6170 manual Trademarks Acknowledgments

Page 5

5.Do not open the system’s back cover. If opening the cover for maintenance is a must, only a trained technician is allowed to do so. Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions:

9Before handling a board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. This will help to discharge any static electricity on your body.

9When handling boards and components, wear a wrist-grounding strap, available from most electronic component stores.

Trademarks Acknowledgments

Acnodes is a trademark of Acnodes Co., Ltd.

IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.

Intel and Pentium are trademarks of Intel Corporation.

MS-DOS, Microsoft C and QuickBASIC are trademarks of Microsoft Corporation.

VIA is a trademark of VIA Technologies, Inc.

SST is a trademark of Silicon Storage Technology, Inc.

UMC is a trademark of United Microelectronics Corporation.

Other brand names and trademarks are the properties of their respective owners.

v

Image 5 Contents
Pentium-M Panel PC Disclaimers FCC Compliance Safety ApprovalsSafety Precautions Trademarks Acknowledgments This page does not contain any information Table of Contents Embedded O.S. Installation Introduction Front Access USB Ports & OSDGeneral Description Most Reliable and Stable Design-Intel Pentium M ProcessorMain CPU board SpecificationsEasy-to-Maintenance Design Back Door „ Standard I/O System„ 17 TFT LCD „ Disk drive housing System SpecificationDimensions Front View Front View and I/O OutletsVGA 2 I/O OutletPackage list CPU and Dram Installation Hardware InstallationDram CPU HDD Installation User’s Manual CD-ROM Installation Put the CD-ROM in the drive bracket and fix it by 6 screws Add-on Card Installation VGA 3 x Serial PortsParallel Port Ethernet RJ-45 Connector Pin AssignmentVESA-ARM Mountings Panel/Wall/Desktop/VESA/RackWall Mount PC 6170 User’s Manual Desktop Kit Assembly Fix two holders by 2 screws Complete Panel-mount Kit Assembly Rack mounting Assembly System Driver InstallationTouch Screen SpecificationDriver Installation- Windows 98/2000/XP/CE.NET/XP-Embedded PC 6170 User’s Manual Identify the communication port and IRQ number Driver Installation- DOSDo Calibration Install PenMount driver Driver Installation- LinuxSet COM3 as touch Dual LAN This page does not contain any information Penmount Touch Screen Embedded O.S. InstallationWindows XP Embedded Calibration Touch Screen Windows CE.NETStandard Cmos Setup Menu SBC83810 Bios SetupTime DateHalt On Drive a type/Drive B typeScsi Advanced Bios FeaturesQuick Power On Self Test Hard Disk Boot PriorityVirus Warning CPU L1 & L2 CacheBoot Other Device First/Second/Third Boot DeviceBoot Up Floppy Seek Boot Up NumLock StatusTypematic Rate Chars/Sec Typematic Rate SettingTypematic Delay Msec Report No FDD For Win Security OptionOS Select for Dram 64MB Sdram CAS latency Time Advanced Chipset FeaturesDram Data Integrity Mode Video Bios Cacheable System Bios CacheableDelayed Transaction Video RAM CacheableIntegrated Peripherals SPP Power on Function IDE HDD Block ModeIDE Primary/Secondary Master/Slave PIO IDE Primary/Secondary Master/Slave UdmaParallel Port Mode UART2 Duplex ModeOnboard FDC Controller Onboard Serial Port 1/PortECP Mode Use DMA S1POS Power Management SetupAcpi Function Power ManagementPM Control by APM Video Off MethodStandby Mode Doze ModeSuspend Mode Video Off AfterPower On by Ring HDD Power DownThrottle Duty Cycle VGA Active MonitorReload Global Timer Events Reset Configuration Data PnP/PCI Configuration SetupPNP OS Installed IRQ Resources Resources Controlled ByDMA Resources Memory ResourcesCurrent FAN1/FAN2 Speed Current CPU TemperaturePC Health Status Speed Spectrum Frequency/Voltage ControlAuto Detect DIMM/PCI Clk Cmos Setup Utility-Copyright Award Software Load Fail-Safe DefaultsLoad Optimized Defaults Y/N? N Load Optimized DefaultsPower Supply FSP180-50PLA1 180W, AC 110~230V Input Power Supply SpecificationHOLD-UP Time @FULL Load Short Circuit Protection Efficiency Shock