Acnodes PC 6170 manual Embedded O.S. Installation, Windows XP Embedded, Penmount Touch Screen

Page 43

PC 6170 User’s Manual

C h a p t e r 4

Embedded O.S. Installation

4.1Windows XP Embedded

Supported devices are as follows:

Onboard Multi I/O

„Floppy drive

„Parallel port

„16C550 UARTs compatible serial port

„IrDA for wireless communication

Onboard IDE

„IDE HDD

„IDE

CDROM USB

PS2 Keyboard and mouse

CRT/LCD display

Dual LAN

Giga LAN

Compact flash

Onboard audio

Touch screen

4.1.1Penmount Touch Screen

PC 6170 has Penmount touch screen on COM3, which is disabled by default.

Before you can use and calibrate it, you should :

1.Set up Penmount touch device driver by executing c:\Program Files\PenMount\setup.exe. When installation is finished, an icon “PM” appears on the Taskbar.

2.Calibrate Penmount touch by clicking on “PM” icon and doing calibration

Embedded O.S. Installation

35

Image 43

Contents

Pentium-M Panel PC Disclaimers FCC Compliance Safety ApprovalsSafety Precautions Trademarks Acknowledgments This page does not contain any information Table of Contents Embedded O.S. Installation Most Reliable and Stable Design-Intel Pentium M Processor Front Access USB Ports & OSDIntroduction General DescriptionEasy-to-Maintenance Design Back Door SpecificationsMain CPU board „ Standard I/O System„ 17 TFT LCD „ Disk drive housing System SpecificationDimensions Front View Front View and I/O OutletsVGA 2 I/O OutletPackage list CPU and Dram Installation Hardware InstallationDram CPU HDD Installation User’s Manual CD-ROM Installation Put the CD-ROM in the drive bracket and fix it by 6 screws Add-on Card Installation Parallel Port 3 x Serial PortsVGA Ethernet RJ-45 Connector Pin AssignmentVESA-ARM Mountings Panel/Wall/Desktop/VESA/RackWall Mount PC 6170 User’s Manual Desktop Kit Assembly Fix two holders by 2 screws Complete Panel-mount Kit Assembly Rack mounting Assembly System Driver InstallationTouch Screen SpecificationDriver Installation- Windows 98/2000/XP/CE.NET/XP-Embedded PC 6170 User’s Manual Identify the communication port and IRQ number Driver Installation- DOSDo Calibration Install PenMount driver Driver Installation- LinuxSet COM3 as touch Dual LAN This page does not contain any information Windows XP Embedded Embedded O.S. InstallationPenmount Touch Screen Calibration Touch Screen Windows CE.NETStandard Cmos Setup Menu SBC83810 Bios SetupTime DateHalt On Drive a type/Drive B typeScsi Advanced Bios FeaturesCPU L1 & L2 Cache Hard Disk Boot PriorityQuick Power On Self Test Virus WarningBoot Up NumLock Status First/Second/Third Boot DeviceBoot Other Device Boot Up Floppy SeekTypematic Delay Msec Typematic Rate SettingTypematic Rate Chars/Sec OS Select for Dram 64MB Security OptionReport No FDD For Win Dram Data Integrity Mode Advanced Chipset FeaturesSdram CAS latency Time Video RAM Cacheable System Bios CacheableVideo Bios Cacheable Delayed TransactionIntegrated Peripherals SPP IDE Primary/Secondary Master/Slave Udma IDE HDD Block ModePower on Function IDE Primary/Secondary Master/Slave PIOOnboard Serial Port 1/Port UART2 Duplex ModeParallel Port Mode Onboard FDC ControllerECP Mode Use DMA S1POS Power Management SetupVideo Off Method Power ManagementAcpi Function PM Control by APMVideo Off After Doze ModeStandby Mode Suspend ModeVGA Active Monitor HDD Power DownPower On by Ring Throttle Duty CycleReload Global Timer Events PNP OS Installed PnP/PCI Configuration SetupReset Configuration Data Memory Resources Resources Controlled ByIRQ Resources DMA ResourcesPC Health Status Current CPU TemperatureCurrent FAN1/FAN2 Speed Auto Detect DIMM/PCI Clk Frequency/Voltage ControlSpeed Spectrum Cmos Setup Utility-Copyright Award Software Load Fail-Safe DefaultsLoad Optimized Defaults Y/N? N Load Optimized DefaultsPower Supply FSP180-50PLA1 180W, AC 110~230V Input Power Supply SpecificationHOLD-UP Time @FULL Load Short Circuit Protection Efficiency Shock