Canon 4.1 manual Click on the Zoom In button

Page 32

S T E P 2

Click on the Zoom In button .

The selected area will be displayed in expanded form.

If you want to enlarge the image again, reduce the size of the area selected with the frame and click the Zoom In button again.

Click the Zoom Out button to restore the view prior to zooming.

Click the Zoom Reset Button to restore the size just after previewing.

Hint

•The image cannot be zoomed unless an area is selected.

•The selection can be zoomed up to six times consecutively. If the selected area is too small, the Zoom In button will be disabled and the selection cannot be zoomed.

32

Image 32

Contents Users Guide How to Make Best Use of the Manuals When you open the boxAbout the Conventions Used in this Guide How to Use this GuideWhere to Look Table of Contents Adjusting Scanned Images Installing Plug-in Module CS-U Operating EnvironmentControl Panel Features Pp -20Image SizeScanning Procedures E PPlug-in Module CS-U Special Features Install Plug-in Module CS-U Quick Start InstructionsStart Plug-in Module CS-U p Position materials for scanning and preview them. pVerify Image Quality with the Browser Function before Specify the Area of the Image to be ScannedSelect the area to be scanned by clicking and dragging Mouse pointer over the imageScan the Image Save the Scanned ImageClick on the Scan button Save the image with Adobe Photoshop LE or other plug-inE P Displaying the Plug-in Module CS-U Control Panel RGB ValuesOperating Procedures Place the original on the scanners document glass ProceduresPositioning Originals Previewing Click on the Preview buttonSelecting the Output Device Setting the Resolution and Magnification Output Device Resolution= 720 dpi, Magnification= 100%To Set the Magnification Factor Set the desired magnification factor on the control panelSetting the Scan Mode Click the arrow beside Scan Mode Select a scan mode from the pop-up menuVerifying the Image before Scanning To Verify the ImageRotating the Image Use these buttons to rotate the imageAspect Ratio Setting PreferencesOutput Device Unit Preview WindowReset Default Settings Shut off lamp timeClose Plug-in After Scan Platen/FilmOperating Procedures Scanning Setting the Scan Area Position the pointer in the preview windowSelect the area you want to enlarge with the zoom function Procedures to ZoomZooming Click on the Zoom In button Scanning To Initiate the ScanSpecify the Scan Area Click close box to guit the Plug-in Module CS-USaving Scanned Images Enter a name for the file and click the Save buttonScanning Film Auto Exposure Save Exposure DataClick on the Scan button Remove Dust and Scratches CanoScan D2400U only Bit Color Bit/14/16bit Grayscale and 24-bit/42/48bit ColorBlack & White Tone Adjustment Tone Adjustment DialogHistogram Settings How to Interpret HistogramsTo Adjust a Histogram How to Adjust HistogramsClick on the OK button Shadow MarkTone Curve Settings Manipulating the GraphTo Edit the Tone Curve Click the OK buttonRelationship Between the Tone Curve Image Brightness Gamma Value =Brightness Brightness and Contrast SettingsContrast To Adjust the Brightness and Contrast Adjusting the Color Balance Operating ProcedureGamma value Gamma Value SettingsMatching the Gamma Value to the Display Characteristics To Change the Gamma Value Settings Adjusting the Threshold Value To Set the Threshold ValueAuto Tone Correction To Set the Auto Tone CorrectionRecommended ColorSyncUnsharp Mask Open the Image menu and select Unsharp MaskDescreen Open the Image menu and select DescreenHigh-speed Scan Mode Select High-speed Scan Mode from the Image menuClick the Save button Saving/Recalling SettingsTo Save Settings in a Settings File To Recall a Settings File Matching Scan Resolution to Purpose Scanning TechniquesAppendices Troubleshooting Problem Scan button cannot be selected Problem Scanning is taking a long time Problem Scanning quality is poor Response Error MessagesError Message Cause Glossary Color DotOptical Resolution GrayscaleHistogram Image FileResolution PixelPlug-in Software Preview AreaScan Mode ShadowsThreshold Value Tone CurveIndex Output device 7, 11, 18, 25Scan 12, 33 Scan area 11 Canon Customer Support Help Desk Canon U.S.A., INC