Yamaha pdm-4210 Operating Instructions, Turning Power On and Off, Indicating lamp, Power OFF

Page 16

23 25

OPERATING INSTRUCTIONS

Indicating lamp

Main power switch

Turning Power On and Off

•To turn the monitor power on, press the main power switch on the monitor main unit to ON, and then press the SUB POWER button or the ON/OFF or ON button on the remote control.

•To turn the monitor power off, press the SUB POWER button or the ON/OFF or OFF button on the remote control, and then set the main power switch on the monitor main unit to OFF.

SUB-POWER button

•During normal use, the main power switch is set in the ON position, and the monitor can then be turned ON/OFF using the SUB POWER button or the ON/OFF button on the remote control.

Indicating lamp

	Indicating	Power status	Operating
	lamp	Power status	Operating
	lamp

	Off	Off	When the main power switch is set
	Off	Off	to OFF.
			to OFF.

			When the main power switch is
		Off	ON, and the OFF button on the
	Lights red	Off	remote control or the SUB POWER
	Lights red	(standby)	remote control or the SUB POWER
		(standby)	button on the underside of the
			button on the underside of the
			front of the frame is OFF.

			When the main power switch is
			ON, and the ON button on the
	Lights green	On	remote control or the SUB POWER
			button on the underside of the
			front of the frame is ON.

			When the main power switch is
			ON, and the ON button on the
		Off	remote control or the SUB POWER
	Lights orange	Off	button on the underside of the
	Lights orange	(Power Save)	button on the underside of the
		(Power Save)	front of the frame is ON.
			front of the frame is ON.
			However, the indicator also light orange
			when the unit is in POWER SAVE mode.

	POWER OFF
	button
	POWER ON	POWER ON/OFF
	POWER ON	button
	button	button
	button
		VOL
		RGB 1 RGB 2 MUTE VOL

AV1 AV2 AV3 AV4

AUTO PinP SIZE RECALL

MENU

When the indicating lamp lights orange or the message “No Sync. Signal”, “Power Save” or “Invalid Scan Freq.” appears on the screen, see “Power Save Mode” or “Symptoms That Appear to be Failures.”

ATTENTION

•Avoid repeatedly turning the monitor on and off at short intervals. Failures might result from such operation.

•Turn off the main power switch if you do not plan to use the monitor for an extended period of time.

•If a power failure occurs while the main unit is running, it will be powered on upon recovery from the failure. Turn off the unit main power switch before you leave the area in which the main unit is located.

OK

ID

ID SET

14

Image 16

Contents PDM-4210 Important Safety Instructions For Canadian customersEnglish Declaration of Conformity Procedure Compliance Information StatementFCC Federal Communications Commission Statement Warning FCC Information for US customers onlyUSER’S Manual Features ContentsNever use the monitor if a problem occurs Use only the correct power outletBe cautious of the power cord connection Be sure to keep safety ground connectionBe careful in handling the battery of the remote control Avoid a high temperature environmentRemove the power cord for complete separation How to view the monitorHow to clean the plasma display panel of the monitor How to clean the cabinet of the monitorPrecautions for the cable connection Precaution during transportationPrecautions for the installation PrecautionsOther precautions Component Names Main UnitControl panel Front RearHandling the Remote Control Component Names Remote controlLoading Batteries Installation Instructions InstallationAnti-tumble measures Securing to a wall or pillarInstallation Instructions Connecting to a PCChoose a safe, level location to install the product Monitor rear panelInstallation Instructions Power Cord Connection Turning Power On and Off Power OFFPower on Power ON/OFF Operating InstructionsOperating Instructions Volume Adjustment Input SwitchingWhen a button is pressed, the volume adjustment Audio MuteSize Switching Input Signal Screen DisplayDisplay area selection diagram RGB input Operating InstructionsAutomatic Adjustment of Screen Position and the Clock Using the Menu Screen On-screen display systemSELECT/ADJUST Independent Operation of Multiple Monitors ID NoReset Picture MenuAmplitude Cut OffTimer Menu Audio MenuFunction Menu 60MinSetup Menu Other Features Language MenuAutomatic Store Menu Display Registration conditionOther Features Signal Check Power Save ModeWhen the RGB1, RGB2 input is selected Status Display ActionImage Retention of Plasma Display Panel Methods to Reduce the Occurrence of Image RetentionAbout screen defects About residual imagesSymptoms That Appear to be Failures TroubleshootingCheck to see if the input signal matches the monitor Troubleshooting Symptoms That Appear to be Failures Troubleshooting Actions to Correct Abnormal Displays ExampleProduct Specifications Signal InputRGB terminal D-sub 15-pin connector Pin Input signalProduct Specifications Signal Input Recommended Signal ListWith Digital RGB signal input RGB1 input DVI terminal DVI-DProduct Specifications Recommended Signal List With Analog RGB signal input RGB2 inputSupplement Connecting to a Video Imaging Device An example of connecting video imaging devicesDVI-STB and RGB component setup Optional Video Unit FunctionDisplay size selection diagram Size buttonAV1 AV2 AV3 RGB2 RGB1 AV4 FullUsing a wide-screen monitor PressOperating Instructions Displaying Multi Picture Pictures SplitYNR Operating Instructions Picture Menu RGB Item is added to the Menu shownOff On System Color SystemVideo Input AV2 1st stepOperating Instructions Setup Menu Audio InputScart Output RGB2 1st step RGB2 2nd stepSymptoms That Seemingly Appear to be Failures Video inputInput connector pin specifications Scart connector pin specificationsAudio OUT Right GND / Shield ChassisWith component input AV1, AV2 and RGB2-component input With R, G, B Video input AV2 and AV4 inputKHz MHz 2003 All rights reserved DVD player To AC outlet AV receiverVideo camera Sat/Cable boxEnglish Remarques PDS-242 PDM-4210, PDM-4210EIncluded in the parts package Unit mm inchesTo ensure correct usage