Yamaha pdm-4210 Compliance Information Statement, FCC Information for US customers only

Page 4

• FCC (Federal Communications Commission) STATEMENT WARNING

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party:

Yamaha Electronics Corporation

Address:

6660 Orangethorpe Avenue

 

Buena Park, CA90620

Telephone:

714-522-9105

Fax:

714-670-0108

Type of Equipment:

High Definition Plasma Monitor

Model Name:

PDM-4210

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1)this device may not cause harmful interference, and

2)this device must accept any interference received including interference that may cause undesired operation. See the user manual instructions if interference to radio reception is suspected.

FCC INFORMATION (for US customers only)

1.IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2.IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3.NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620.

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

2

Image 4
Contents PDM-4210 Important Safety Instructions For Canadian customersEnglish Declaration of Conformity Procedure Compliance Information StatementFCC Federal Communications Commission Statement Warning FCC Information for US customers onlyUSER’S Manual Features ContentsNever use the monitor if a problem occurs Use only the correct power outletBe cautious of the power cord connection Be sure to keep safety ground connectionBe careful in handling the battery of the remote control Avoid a high temperature environmentRemove the power cord for complete separation How to view the monitorHow to clean the plasma display panel of the monitor How to clean the cabinet of the monitorPrecautions for the cable connection Precaution during transportationPrecautions for the installation PrecautionsOther precautions Component Names Main UnitControl panel Front RearHandling the Remote Control Component Names Remote controlLoading Batteries Installation Instructions InstallationAnti-tumble measures Securing to a wall or pillarInstallation Instructions Connecting to a PCChoose a safe, level location to install the product Monitor rear panelInstallation Instructions Power Cord Connection Turning Power On and Off Power OFFPower on Power ON/OFF Operating InstructionsOperating Instructions Volume Adjustment Input SwitchingWhen a button is pressed, the volume adjustment Audio MuteSize Switching Input Signal Screen DisplayDisplay area selection diagram RGB input Operating InstructionsAutomatic Adjustment of Screen Position and the Clock Using the Menu Screen On-screen display systemSELECT/ADJUST Independent Operation of Multiple Monitors ID NoReset Picture MenuAmplitude Cut OffTimer Menu Audio MenuFunction Menu 60MinSetup Menu Other Features Language MenuAutomatic Store Menu Display Registration conditionOther Features Signal Check Power Save ModeWhen the RGB1, RGB2 input is selected Status Display ActionImage Retention of Plasma Display Panel Methods to Reduce the Occurrence of Image RetentionAbout screen defects About residual imagesSymptoms That Appear to be Failures TroubleshootingCheck to see if the input signal matches the monitor Troubleshooting Symptoms That Appear to be Failures Troubleshooting Actions to Correct Abnormal Displays ExampleProduct Specifications Signal InputRGB terminal D-sub 15-pin connector Pin Input signalProduct Specifications Signal Input Recommended Signal ListWith Digital RGB signal input RGB1 input DVI terminal DVI-DProduct Specifications Recommended Signal List With Analog RGB signal input RGB2 inputSupplement Connecting to a Video Imaging Device An example of connecting video imaging devicesDVI-STB and RGB component setup Optional Video Unit FunctionDisplay size selection diagram Size buttonAV1 AV2 AV3 RGB2 RGB1 AV4 FullUsing a wide-screen monitor PressOperating Instructions Displaying Multi Picture Pictures SplitYNR Operating Instructions Picture Menu RGB Item is added to the Menu shownOff On System Color SystemVideo Input AV2 1st stepOperating Instructions Setup Menu Audio InputScart Output RGB2 1st step RGB2 2nd stepSymptoms That Seemingly Appear to be Failures Video inputInput connector pin specifications Scart connector pin specificationsAudio OUT Right GND / Shield ChassisWith component input AV1, AV2 and RGB2-component input With R, G, B Video input AV2 and AV4 inputKHz MHz 2003 All rights reserved DVD player To AC outlet AV receiverVideo camera Sat/Cable boxEnglish Remarques PDS-242 PDM-4210, PDM-4210EIncluded in the parts package Unit mm inchesTo ensure correct usage