BenQ MX716, MX717 user manual Adjusting the projected image, Adjusting the projection angle

Page 20
Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes.
Be careful when you press the quick- release button as it is close to the exhaust vent where hot air comes from.

Adjusting the projected image

Adjusting the projection angle

To adjust the projector (MX716):

1.Press the quick-release button and lift the front of the projector. Once the image is positioned where you want it, release the quick-release button to lock the foot in position.

2.Screw the rear adjuster foot to fine-tune the horizontal angle.

To retract the foot, hold up the projector while pressing the quick-release button, then slowly lower the projector. Screw the rear adjuster foot in a reverse direction.

To adjust the projector (MX717):

Screw the adjuster feet to fine-tune the horizontal angle.

To retract the feet, screw the adjuster feet in a reverse direction.

MX716

1

2

MX717

If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image becomes

trapezoidal. To correct this situation, see "Switching input signal" on page 26 for details.

Auto-adjusting the image

In some cases, you may need to optimize the picture quality. To do this, press AUTO on the projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality.

The current source information will be displayed in the corner of the screen for 3 seconds.

This function is only available when PC signal (analog RGB) is selected.

20 Operation

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Welcome Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Rear/lower side Projector exterior viewFront/upper side Controls and functions Remote control Network Setting Not available TestSource selection buttons COMPUTER-1, COMPUTER-2 Network Not availableVolume + Operating the Laser pointerMute MIC/VOL +/- Not availableRemote control effective range Replacing the remote control batteries Positioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeConnection ConnectionConnecting video source devices Connecting audioTerminal name Terminal appearance BestOperation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Correcting keystoneUsing the menus HighlightUsing a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press EnterIf you forget the password Entering the password recall procedurePress ENTER. The message Input Current Password appears Changing the passwordDisabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerSelection Description To cancel the timer, perform the following steps Remote paging operationsFreezing the image Hiding the imageTo activate the High Altitude Mode Using the remote controlUsing the OSD menu Operating in a high altitude environmentAdjusting the sound Adjusting the sound levelTurning off the Power On/Off Ring Tone Muting the soundControlling the projector through a LAN environment Cable connectionIf you are in a Dhcp environment If you are in a non-DHCP environmentControlling the projector remotely through a web browser Iiii Iiiv Direct power off Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system System Setup Basic Time Sec Menu Settings Menu PositionRight/Bottom-Left Hr/12 hrAdvanced Description of each menu Picture Mode TemperatureSave Settings Display menu Picture menu FunctionTimer SettingsSearch Color SpaceSystem Setup Basic men Function Description OperationPanel Key LockSystem Setup Advanced menu Function Description High AltitudeAudio LampSystem Setup Advanced menu Function Description Reset AllStandby NetworkInformation menu Function Description CurrentSystem StatusMaintenance Care of the projectorSetting Lamp Mode as Economic Lamp informationGetting to know the lamp hour Extending lamp lifeTiming of replacing the lamp Status MessageReplacing the lamp MX716Use the handle to slowly pull the lamp out As shown in the figure, lower the new lamp Resetting the lamp timer Tighten the screws that secures the lamp coverIndicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installation Ceiling Mount screw M4 Max L = 8 mmKHz Timing chartSupported timing for PC input Resolution Mode Frequency KHz MHz Supported timing for Hdmi Hdcp inputSupported timing for Component-YPbPrinput TimingHorizontal Frequency Hz Frequency kHzSupported timing for Video and S-Video inputs Warranty and Copyright information Limited warrantyCopyright Disclaimer

MX717, MX716 specifications

The BenQ MX716 and MX717 are versatile projectors designed for educational and professional environments, offering a blend of performance, reliability, and user-friendly features. Both models are equipped with DLP technology, ensuring vibrant colors and sharp images, making them ideal for classrooms, conference rooms, and other presentation settings.

One of the standout features of the BenQ MX716 and MX717 is their brightness. With a brightness level of up to 4000 ANSI lumens, these projectors are capable of delivering clear visuals even in well-lit rooms. This high lumens output makes it easier for viewers to see detailed graphics and text, ensuring that presentations remain engaging and effective.

Both models offer a native XGA resolution of 1024 x 768 pixels, providing a solid foundation for detailed visual displays. The projectors support a variety of resolutions, including 1080p, ensuring compatibility with various multimedia sources. This flexibility allows users to connect laptops, DVDs, and other devices without compromising on image quality.

The contrast ratio is another key feature, with both projectors offering a high contrast ratio of 13,000:1. This impressive ratio enhances image depth and clarity, resulting in more lifelike colors and sharper text. As a result, presentations appear more professional and easy to follow, improving overall communication.

In terms of connectivity, the BenQ MX716 and MX717 come equipped with multiple inputs, including HDMI, VGA, and USB ports. This variety facilitates seamless connections with diverse devices, essential for modern multimedia environments. Additionally, the built-in speakers deliver decent sound quality, enhancing the overall presentation experience without requiring external audio equipment.

BenQ has also integrated eco-friendly technologies into these models, achieving low power consumption and extended lamp life. The SmartEco technology intelligently adjusts lamp power based on the content being displayed, which not only reduces energy usage but also extends the life of the lamp up to 10,000 hours.

Portability is another consideration, as both projectors are designed to be lightweight and compact, making them easy to transport between different locations. The user-friendly interface, along with quick setup and installation processes, confirms BenQ’s commitment to providing hassle-free solutions for its users.

In summary, the BenQ MX716 and MX717 projectors combine high brightness, excellent image quality, and user-friendly features, making them ideal choices for educational and corporate environments. Whether for lectures, meetings, or presentations, these projectors ensure optimal performance and reliability.
Top Page Image Contents