BenQ MX717 Indicators, Light Status & Description Power events, Lamp events, Thermal events

Page 57

Indicators

Light

Status & Description

					Power events

	Orange	Off	Off	Stand-by mode.
	Green	Off	Off	Powering up.
	Flashing	Off	Off	Powering up.
	Flashing
	Green	Off	Off	Normal operation.
				• The projector needs 90 seconds to cool down as it was
					abnormally shut down without the normal cooling down
					process.
	Orange	Off	Off	• The projector needs to cool for 90 seconds after the
	Flashing	Off	Off		power is turned off.
	Flashing				power is turned off.
				• The projector has shut down automatically. If you try to
					re-start the projector, it will shut down again. Please
					contact your dealer for assistance.
					Lamp events
				The projector has shut down automatically. If you try to re-
	Off	Off	Red	start the projector, it will shut down again. Please contact
				your dealer for assistance.
	Orange	Off	Red	1.	The projector needs 90 seconds to cool down. Or
	Orange	Off	Red	2.	Please contact your dealer for assistance.
				2.	Please contact your dealer for assistance.

Thermal events

Off	Red	Off
Off	Red	Red
Off	Red	Green
Off	Red	Orange
Orange	Red	Red
Orange	Red	Green
Red	Red	Red
Red	Red	Green
Green	Red	Red
Green	Red	Green
Off	Green	Red
Off	Green	Orange
Off	Orange	Red

The projector has shut down automatically. If you try to re- start the projector, it will shut down again. Please contact your dealer for assistance.

Maintenance 57

Image 57

Contents

Welcome Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Projector exterior view Front/upper sideRear/lower side Controls and functions Network Setting Not available Test Remote controlSource selection buttons COMPUTER-1, COMPUTER-2 Network Not availableOperating the Laser pointer Volume +Mute MIC/VOL +/- Not availableRemote control effective range Replacing the remote control batteries Choosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsConnection ConnectionConnecting audio Connecting video source devicesTerminal name Terminal appearance BestStarting up the projector OperationAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Correcting keystone Fine-tuning the image size and clarityHighlight Using the menusUtilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press EnterEntering the password recall procedure If you forget the passwordChanging the password Disabling the password functionPress ENTER. The message Input Current Password appears Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Setting the presentation timer Selection DescriptionTop-Left Bottom-Left Top-Right Bottom-Right Remote paging operations To cancel the timer, perform the following stepsFreezing the image Hiding the imageUsing the remote control To activate the High Altitude ModeUsing the OSD menu Operating in a high altitude environmentAdjusting the sound level Adjusting the soundTurning off the Power On/Off Ring Tone Muting the soundCable connection Controlling the projector through a LAN environmentIf you are in a Dhcp environment If you are in a non-DHCP environmentControlling the projector remotely through a web browser Iiii Iiiv Shutting down the projector Direct power offMenu operation Menu systemMain menu Sub-menu Options Time Sec Menu Settings Menu Position System Setup BasicRight/Bottom-Left Hr/12 hrAdvanced Description of each menu Temperature Picture ModeSave Settings Display menu Picture menu FunctionSettings TimerSearch Color SpaceOperation System Setup Basic men Function DescriptionPanel Key LockAltitude System Setup Advanced menu Function Description HighAudio LampReset All System Setup Advanced menu Function DescriptionStandby NetworkCurrent Information menu Function DescriptionSystem StatusCare of the projector MaintenanceLamp information Setting Lamp Mode as EconomicGetting to know the lamp hour Extending lamp lifeStatus Message Timing of replacing the lamp MX716 Replacing the lampUse the handle to slowly pull the lamp out As shown in the figure, lower the new lamp Tighten the screws that secures the lamp cover Resetting the lamp timerLight Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsDimensions Ceiling Mount screw M4 Max L = 8 mm Ceiling mount installationTiming chart Supported timing for PC inputKHz Supported timing for Hdmi Hdcp input Resolution Mode Frequency KHz MHzTiming Supported timing for Component-YPbPrinputHorizontal Frequency Hz Frequency kHzSupported timing for Video and S-Video inputs Limited warranty Warranty and Copyright informationCopyright Disclaimer