BenQ MX716, MX717 user manual Iiii Iiiv

Page 38

The tools page allows you to manage the projector, configure the Network settings and secure access of remote network operation on this projector.

iiii

iiiv

v

i.You can name the projector, keep track of its location and the person in charge of it.

ii.You can adjust the Network Settings.

iii.Once set, access to the remote network operation on this projector has been password-protected.

iv.Once set, access to the tools page has been password-protected.

After making the adjustments, press the Send button and the data will be saved in the projector.

v.Press Exit to go back to the remote network operation page. The info page displays the information and status of this projector.

Press Exit to go back to the remote network operation page.

6.For more information, visit http://www.crestron.com. If you are an IT administrator and would like to manage multiple devices through one interface, you can download Crestron Roomview at www.crestron.com/getroomview.

38 Operation

Page 37 Page 39
Image 38
Page 37 Page 39
Contents
Welcome Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Rear/lower side Projector exterior viewFront/upper side Controls and functions Source selection buttons COMPUTER-1, COMPUTER-2 Remote controlNetwork Setting Not available Test Network Not availableMute Volume +Operating the Laser pointer MIC/VOL +/- Not availableRemote control effective range Replacing the remote control batteries Front Table Positioning your projectorChoosing a location Front CeilingProjection dimensions Obtaining a preferred projected image sizeConnection ConnectionTerminal name Terminal appearance Connecting video source devicesConnecting audio BestOperation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Correcting keystoneUsing the menus HighlightSetting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press EnterIf you forget the password Entering the password recall procedurePress ENTER. The message Input Current Password appears Changing the passwordDisabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerSelection Description Freezing the image To cancel the timer, perform the following stepsRemote paging operations Hiding the image Using the OSD menu To activate the High Altitude Mode Using the remote control Operating in a high altitude environmentTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Muting the soundIf you are in a Dhcp environment Controlling the projector through a LAN environmentCable connection If you are in a non-DHCP environmentControlling the projector remotely through a web browser Iiii Iiiv Direct power off Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system Right/Bottom-Left System Setup BasicTime Sec Menu Settings Menu Position Hr/12 hrAdvanced Description of each menu Save Settings Picture ModeTemperature Display menu Picture menu FunctionSearch TimerSettings Color SpacePanel Key System Setup Basic men Function DescriptionOperation LockAudio System Setup Advanced menu Function Description HighAltitude LampStandby System Setup Advanced menu Function DescriptionReset All NetworkSystem Information menu Function DescriptionCurrent StatusMaintenance Care of the projectorGetting to know the lamp hour Setting Lamp Mode as EconomicLamp information Extending lamp lifeTiming of replacing the lamp Status MessageReplacing the lamp MX716Use the handle to slowly pull the lamp out As shown in the figure, lower the new lamp Resetting the lamp timer Tighten the screws that secures the lamp coverLamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installation Ceiling Mount screw M4 Max L = 8 mmKHz Timing chartSupported timing for PC input Resolution Mode Frequency KHz MHz Supported timing for Hdmi Hdcp inputHorizontal Supported timing for Component-YPbPrinputTiming Frequency Hz Frequency kHzSupported timing for Video and S-Video inputs Copyright Warranty and Copyright informationLimited warranty Disclaimer
Top Page Image Contents