BenQ MX716, MX717 user manual Controlling the projector through a LAN environment, Cable connection

Page 36

Controlling the projector through a LAN environment

You can manage and control the projector from one or more remote computers when they are properly connected to the same local area network.

MX716

MX717

Cable connection

If you are in a DHCP environment:

1.Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector and the other end to the RJ45 port on your Ethernet or router.

2.Do one of the following:

•Press NETWORK SETTING on the remote control. The Network Settings page is displayed.

•Press MENU/EXIT and then press / until the SYSTEM SETUP:

Advanced menu is highlighted. Press to highlight Network Settings and press ENTER. The Network Settings page is displayed.

3.Highlight Wired LAN and press ENTER.

4.Make sure the Status is Connect.

5.Press to highlight DHCP and press / to select On.

6.Press to highlight Apply and press ENTER.

7.Re-enter the Network Settings > Wired LAN page. The IP Address, Subnet Mask, Default Gateway, and DNS settings will be displayed. Note down the IP address displayed in the IP Address row.

If the IP Address still does not appear, contact your ITS administrator.

If you are in a non-DHCP environment:

1.Repeat steps 1-4 above.

2.Press to highlight DHCP and press / to select Off.

3.Contact your ITS administrator for information on the IP Address, Subnet Mask, Default Gateway, and DNS settings.

4.Press to select the item you want to modify and press ENTER.

36 Operation

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Welcome Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Front/upper sideRear/lower side Controls and functions Remote control Network Setting Not available TestSource selection buttons COMPUTER-1, COMPUTER-2 Network Not availableVolume + Operating the Laser pointerMute MIC/VOL +/- Not availableRemote control effective range Replacing the remote control batteries Positioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeConnection ConnectionConnecting video source devices Connecting audioTerminal name Terminal appearance BestOperation Starting up the projectorAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarity Correcting keystoneUsing the menus HighlightUsing a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press EnterIf you forget the password Entering the password recall procedureChanging the password Disabling the password functionPress ENTER. The message Input Current Password appears Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Setting the presentation timer Selection DescriptionTop-Left Bottom-Left Top-Right Bottom-Right To cancel the timer, perform the following steps Remote paging operationsFreezing the image Hiding the imageTo activate the High Altitude Mode Using the remote controlUsing the OSD menu Operating in a high altitude environmentAdjusting the sound Adjusting the sound levelTurning off the Power On/Off Ring Tone Muting the soundControlling the projector through a LAN environment Cable connectionIf you are in a Dhcp environment If you are in a non-DHCP environmentControlling the projector remotely through a web browser Iiii Iiiv Direct power off Shutting down the projectorMenu operation Menu systemMain menu Sub-menu Options System Setup Basic Time Sec Menu Settings Menu PositionRight/Bottom-Left Hr/12 hrAdvanced Description of each menu Picture Mode TemperatureSave Settings Display menu Picture menu FunctionTimer SettingsSearch Color SpaceSystem Setup Basic men Function Description OperationPanel Key LockSystem Setup Advanced menu Function Description High AltitudeAudio LampSystem Setup Advanced menu Function Description Reset AllStandby NetworkInformation menu Function Description CurrentSystem StatusMaintenance Care of the projectorSetting Lamp Mode as Economic Lamp informationGetting to know the lamp hour Extending lamp lifeTiming of replacing the lamp Status MessageReplacing the lamp MX716Use the handle to slowly pull the lamp out As shown in the figure, lower the new lamp Resetting the lamp timer Tighten the screws that secures the lamp coverIndicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installation Ceiling Mount screw M4 Max L = 8 mmTiming chart Supported timing for PC inputKHz Resolution Mode Frequency KHz MHz Supported timing for Hdmi Hdcp inputSupported timing for Component-YPbPrinput TimingHorizontal Frequency Hz Frequency kHzSupported timing for Video and S-Video inputs Warranty and Copyright information Limited warrantyCopyright Disclaimer

MX717, MX716 specifications

The BenQ MX716 and MX717 are versatile projectors designed for educational and professional environments, offering a blend of performance, reliability, and user-friendly features. Both models are equipped with DLP technology, ensuring vibrant colors and sharp images, making them ideal for classrooms, conference rooms, and other presentation settings.

One of the standout features of the BenQ MX716 and MX717 is their brightness. With a brightness level of up to 4000 ANSI lumens, these projectors are capable of delivering clear visuals even in well-lit rooms. This high lumens output makes it easier for viewers to see detailed graphics and text, ensuring that presentations remain engaging and effective.

Both models offer a native XGA resolution of 1024 x 768 pixels, providing a solid foundation for detailed visual displays. The projectors support a variety of resolutions, including 1080p, ensuring compatibility with various multimedia sources. This flexibility allows users to connect laptops, DVDs, and other devices without compromising on image quality.

The contrast ratio is another key feature, with both projectors offering a high contrast ratio of 13,000:1. This impressive ratio enhances image depth and clarity, resulting in more lifelike colors and sharper text. As a result, presentations appear more professional and easy to follow, improving overall communication.

In terms of connectivity, the BenQ MX716 and MX717 come equipped with multiple inputs, including HDMI, VGA, and USB ports. This variety facilitates seamless connections with diverse devices, essential for modern multimedia environments. Additionally, the built-in speakers deliver decent sound quality, enhancing the overall presentation experience without requiring external audio equipment.

BenQ has also integrated eco-friendly technologies into these models, achieving low power consumption and extended lamp life. The SmartEco technology intelligently adjusts lamp power based on the content being displayed, which not only reduces energy usage but also extends the life of the lamp up to 10,000 hours.

Portability is another consideration, as both projectors are designed to be lightweight and compact, making them easy to transport between different locations. The user-friendly interface, along with quick setup and installation processes, confirms BenQ’s commitment to providing hassle-free solutions for its users.

In summary, the BenQ MX716 and MX717 projectors combine high brightness, excellent image quality, and user-friendly features, making them ideal choices for educational and corporate environments. Whether for lectures, meetings, or presentations, these projectors ensure optimal performance and reliability.
Top Page Image Contents