Brother HL-760 Series manual Control Features Set by the Brother Printer Driver, Protection

Page 34

CHAPTER 3 CONTROL PANEL

Control Features Set by the Brother Printer Driver

Page Protection

If the printed images are too complex to print, the printer may print a partial image on the page. If this occurs, the printer has lost some print data and will indicate a “print overrun” error by printing an error report.

The page protection feature allows the printer to create the image to be printed in memory before physically moving the paper through the printer. Therefore, setting page protection to ON may eliminate the “PRINT OVERRUN” error.

The “AUTO” setting does not require additional memory and it automatically uses page protection only when it is necessary. Occasionally, when AUTO page protection is on, processing complex print data may be slightly delayed.

✒Note

To set the Page Protection to A4, Letter or Legal paper sizes, the following

total capacity of memory is required.
		300 dpi	600 dpi
	Letter/A4	2 Mbytes	6 Mbytes
	Legal	3 Mbytes	6 Mbytes

If your printer does not have enough memory for page protection, your document may be printed at 300 dpi.

You can set this function in the following ways.

∙The supplied printer driver for Windows 95/Windows 3.1

∙The supplied RPC program for DOS

For details of the settings, see the relevant help screen.

CHAPTER 3 –5

Image 34

Contents Please read this manual thoroughly before using the printer Brother Laser PrinterShipment of the Printer Laser Printer HL-760 Series User’s Guide Trademarks Compilation and Publication NoticeDefinitions of Warnings, Cautions, and Notes To Use the Printer SafelyTable of Contents Index Industry Canada Compliance Statement For Canada Only RegulationsInternational Energy Star Compliance Statement Radio Interference 220-240 V Model Only Laser Safety For 110-120 V Model OnlyFDA Regulations For 110-120 V Model Only IEC 825 Specification For 220-240 V Model Only Declaration of Conformity For EuropeImportant For Your Safety Geräuschemission / Acoustic Noise Emission For Germany OnlyImportant Wiring Information For U.K. only Finding Out How to Use the Printer About the GuidebooksAbout Your Printer Printer OverviewDpi Resolution and 6 ppm Printing Speed FeaturesVersatile Paper Handling Popular Printer Emulation Support Remote Printer Console Program for DOSOptional Apple Macintosh Interface Enhanced Memory Management Environment-Friendly Economy Printing ModeSleep Mode Power Save Mode Low Running CostOperating and Storage Environment Power SupplyEnvironment Introduction Paper Specifications Paper Type Paper SizeRemarks Fan the Paper Straighten the PaperEnvelopes MULTI-PURPOSE Sheet Feeder Loading Paper into the Feeder Opening the Feeder Loading Paper or Envelopes in the FeederPaper Jams in Chapter Two Side Printing Manual Duplexing When you load more than one sheet of paper manually When you load one sheet of paper manuallyManual Feed Slot Paper Handling Output Tray and Paper Support Wire Opening the Output Tray Extending the Extension Support WireLamps and Switch Ready Paper LampData Toner Lamp Alarm LampDrum Lamp Switch Other Control FeaturesSleep Mode Test Print Mode Lamp Lit Choice FunctionControl Features Set by the Brother Printer Driver ProtectionSerial Interface Board RS-100M Selecting the RS-422A Apple or RS-232C IBM Serial InterfaceSetting the Serial Interface Parameters Selecting the RS-422A Apple Or RS-232C IBM Serial InterfaceDTR only BitsBit OffConnecting the Serial Interface Cable NoneOptions Additional Memory Minimum Memory Recommendation including resident memoryInstalling the Simm Unplug the Power Cord Disconnect the Interface CableRemoving the Main Controller Board Chapter Maintenance Replacing the Toner CartridgeRemoving the Drum Unit Turning the Lever to Close the Shutter Removing the Old Toner Cartridge Installing the Toner Cartridge Into the Drum Unit Replacing the Drum Unit Drum Unit Nearly at the End of its Life10 Removing the Drum Unit ∙ Do not remove the starter sheet 12 Removing the Toner Cartridge15 Installing the Drum Unit Adjusting the Print Density 17 Adjusting the Print Density DialCleaning the Printer Cleaning the Printer ExteriorCleaning the Printer Interior and Drum Unit 20 Turning off the Switch and UnpluggingGently wipe the scanner window with a soft dry cloth 23 Cleaning the Primary Corona Wire 24 Removing the Drum Unit Assembly RE-PACKING the Printer25 Placing the Drum Unit in the Plastic Bag Blinking Lamp Error Action Alarm Indications AT a GlanceOperator Calls Error Action Troubleshooting Service Calls Paper Jams Locating Paper Jam PositionDo Not Pull the Jammed Paper from the Output Tray Paper Jam near the Drum Unit Setting Up the Printer for Windows Setting Up the Printer HardwareQuestion Recommendation Setting Up the Printer for DOS QuestionPaper Handling Printing Serial Inter Face Board RS100MPrint Quality White Stripes or Faint ImagesToner scatters and stains the printed Printed pages are blurred at the center or either edge Printer Specifications Appendix aFunctions Electrical and Mechanical Parallel Interface Specifications Data StrobeFig. A-1 Parallel Interface Cable Scalable Fonts Resident FontsBitmapped Fonts Intellifont Compatible FontsHP LaserJet 5P Mode Symbol SETS/CHARACTER SetsOCR Symbol Sets Epson ModeIndex Slide switch